Civilize Mart

 91 000 74051 Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

 91 000 74051 Dr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of water based paints.

 91 000 74051 Dr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of water based paints.

 91 000 74051 Dr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of water based paints.

 91 000 74051 Dr. Fixit Sureseal is single component specially designed waterproof protective coating that prevents damp patches on Internal & External walls & Roof of building. When cured forms breathable, very tough yet elastic film which develops strong bonding to damp surfaces and does not allow water to pass through. Dr. Fixit Sureseal is tintable may be applied over previous exterior coatings in sound condition.

 91 000 74051 Dr. Fixit Bathseal Select White is a single-component, ready-to-use acrylic-based flexible waterproofing coating specially formulated for bathrooms, wet zones, terraces, and internal & external walls. It has high elasticity with crack-bridging ability up to ~3 mm, excellent adhesion, durable waterproof membrane, and is applied directly with brush or roller. It protects surfaces from water seepage, dampness, and forms a seamless, white protective layer.
Key Features & BenefitsSingle component, saves time—no mixing of parts. Flexible acrylic membrane with high elongation (≈ 250 %) and crack-bridging up to ~3 mm. Low VOC content (environmentally better). Waterproof — prevents water infiltration in wet areas (bathrooms, terraces). White finish—good aesthetic, can brighten small areas.
Q1. Where is Bathseal Select White used?Bathrooms, wet zones, internal & external walls, terraces, places prone to dampness and water splash.Often used in sealing basements or on walls retained behind bathrooms.Q2. How many coats are needed and how to apply?Two coats are recommended. First coat allowed to dry, then apply second. Apply with brush/roller over clean, prepared surface.Q3. What crack width can it bridge?Up to around 3 mm crack-bridging capacity. Q4. Is it safe / what are the odor / VOC issues?Low VOC content. Single component formulation helps with ease of use.Q5. Approximate price?PLEASE VISIT CIVILIZEMART OR CONTACTQ6. What surface prep is required?Surfaces should be clean, free of loose particles, oil, mildew, dust.Repair large cracks first. Maybe prime if the substrate is very porous.

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART

 91 000 74051 Dr. Fixit Roofseal Ultra is an elastomeric polyurethane hybrid next generation liquid applied protective roof waterproofing coating designed to resist water intrusion. The high solids polymers in Dr. Fixit Roofseal Ultra provides weather resistance mechanical properties, long-term durability. Upon curing, forming thick protective totally watertight, highly elastic and durable membrane without seams or joints. The waterproofing membrane is resistant to UV radiation, with high solar –reflectance index 106 and highly resistant to ponding water.

 91 000 74051 Dr. Fixit Roofseal Ultra is an elastomeric polyurethane hybrid next generation liquid applied protective roof waterproofing coating designed to resist water intrusion. The high solids polymers in Dr. Fixit Roofseal Ultra provides weather resistance mechanical properties, long-term durability. Upon curing, forming thick protective totally watertight, highly elastic and durable membrane without seams or joints. The waterproofing membrane is resistant to UV radiation, with high solar –reflectance index 106 and highly resistant to ponding water.

 91 000 74051 Dr. Fixit Roofseal Select is a single-component, acrylic (acrylate-silicone) elastomeric coating engineered for robust terrace waterproofing. Upon curing, it forms a tough, elastic membrane capable of >300% elongation, providing crack bridging, UV resistance, and reflective cooling—able to reduce surface temperature by up to 10 °C.
Highlights:
High-building system: Achieves up to 1 mm film thickness in 3 coatsCrack resilience: Expands and contracts with roof movementCool Roof Effect: Especially with white variant10-Year WarrantyLow-VOC & Non-toxic, suitable for foot traffic
FAQ (Questions & Answers)
Q1. What is Dr. Fixit Roofseal Select used for?It’s a heavy-duty acrylic waterproof coating for terraces, brick-bat coba, screeds, and tiled roofs—preventing water ingress while reflecting heat.
Q2. How many coats and what coverage?Apply a self-priming coat (diluted 50% with water), then 2–3 undiluted coats. Coverage typically 1.5–1.6 L/m² for full build-up.
Q3. What benefits does it offer?Bridges cracks up to 2 mmReduces surface temperature by up to 10 °CTough, UV-resistant, and elastic (>300% elongation)Breathable and low-VOCovered by a 10-year warranty
Q4. What colors and pack sizes are available?Comes in White (cooling), Grey, and Terracotta shades in 4 L and 20 L buckets.
Q5. How long is the shelf life?Shelf life of 36 months when stored in sealed containers at 10–30 °C.
Q6. What is the price?₹6,800for 20 L (approx., from authorized dealer)₹1,390 for 4 LPrices vary by seller—contact CivilizeMart for the latest rates and bulk deals.

 91 000 74051 Dr. Fixit Roofseal Select is a single-component, acrylic (acrylate-silicone) elastomeric coating engineered for robust terrace waterproofing. Upon curing, it forms a tough, elastic membrane capable of >300% elongation, providing crack bridging, UV resistance, and reflective cooling—able to reduce surface temperature by up to 10 °C.
Highlights:
High-building system: Achieves up to 1 mm film thickness in 3 coatsCrack resilience: Expands and contracts with roof movementCool Roof Effect: Especially with white variant10-Year WarrantyLow-VOC & Non-toxic, suitable for foot traffic
FAQ (Questions & Answers)
Q1. What is Dr. Fixit Roofseal Select used for?It’s a heavy-duty acrylic waterproof coating for terraces, brick-bat coba, screeds, and tiled roofs—preventing water ingress while reflecting heat.
Q2. How many coats and what coverage?Apply a self-priming coat (diluted 50% with water), then 2–3 undiluted coats. Coverage typically 1.5–1.6 L/m² for full build-up.
Q3. What benefits does it offer?Bridges cracks up to 2 mmReduces surface temperature by up to 10 °CTough, UV-resistant, and elastic (>300% elongation)Breathable and low-VOCovered by a 10-year warranty
Q4. What colors and pack sizes are available?Comes in White (cooling), Grey, and Terracotta shades in 4 L and 20 L buckets.
Q5. How long is the shelf life?Shelf life of 36 months when stored in sealed containers at 10–30 °C.
Q6. What is the price?₹6,800for 20 L (approx., from authorized dealer)₹1,390 for 4 LPrices vary by seller—contact CivilizeMart for the latest rates and bulk deals.

 91 000 74051 Dr. Fixit Pidigrout 10M - High-Strength, Non-Shrink Grout is a ready-to-use, free-flowing cementitious grout that provides very high strength and does not shrink after setting. It is specially designed for heavy-duty applications where a strong, stable, and reliable foundation is critical, such as under heavy machinery, bridge bearings, and structural columns.
Key Benefits:
High Strength: Achieves compressive strength of over 800 ksc (approx. 80 MPa) in 28 days.Non-Shrink: Expands slightly upon setting to ensure a perfect, full-contact bond with the base.Free-Flowing: Easily flows into tight spaces and under base plates without needing vibration.Ready-to-Use: Just add water and mix for easy application.Heavy-Duty: Ideal for machinery foundations, precast structures, and turbine bases.Approximate Market Price: 399 - 499 per 25 kg bag (Please contact for the best bulk price!)
Questions and Answers:Q1: What is Pidigrout 10M used for?A: It is used for grouting applications that require high strength and stability. Common uses include fixing heavy machinery bases, bridge bearing pads, boiler foundations, turbine generator plates, and structural columns.Q2: How much water should be added to a 25kg bag?A: For a free-flowing consistency, add 4.0 to 4.5 liters of clean water per 25kg bag. For a drier, trowelable mix, use 3.25 to 3.5 liters of water. Never add extra water.Q3: What is the coverage or yield from one bag?A: One 25kg bag mixed with water yields approximately 12.5 liters of grout.Q4: What is the approximate price?A: The approximate price for a 25kg bag is 499 TO 518. Contact CIVILIZEMART us for a precise quote, especially for bulk orders.Q5: How strong is this grout?A: It is very high-strength. It achieves over 350 ksc in 24 hours and reaches a final compressive strength of over 800 ksc (80 MPa) in 28 days.Q6: Does it shrink or expand?A: It is a non-shrink grout. It undergoes a slight controlled expansion during setting to compensate for any shrinkage, ensuring a tight, void-free fill under the base plate.Q7: What is the shelf life?A: When stored in a sealed container in a shaded area, it has a shelf life of up to 1 year.Q8: Can it be used for deep fills?A: Yes, for fills deeper than 75mm, you can add approximately 10 kg of clean, washed 10mm crushed aggregates to each 25kg bag of grout to reduce heat generation and cost.Q9: What precautions should be taken during application?A:Soak the base surface with water for 24 hours before grouting.Ensure the shuttering (formwork) is completely leak-proof.Do not add extra water to the mix.Cure the grout after placement by covering it with wet jute bags or using a curing compound.

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Pidiseal PS43, Grey is a two-part elastomeric sealant based on a liquid polysulphide polymer which when mixed with accelerator (curing agent) cures by chemical reaction to form a tough, flexible rubber seal. This sealant has excellent fuel resistance, adhesion to different substrates like masonry, concrete with excellent movement accommodation. It is far more superior to conventional joint sealant materials such as bitumen, mastics and expansion-sheets.

 91 000 74051 We have marked a remarkable position in the market by offering the best quality array of products to our clients.

 91 000 74051 Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

91 000 74051 What it is: A high-quality, liquid polymer additive for cement, concrete, and plaster. It is designed to provide integral waterproofing and significantly enhance strength and durability.Key Advantages:Complete Waterproofing: Penetrates the mix to block water seepage from within, making structures like terraces and basements watertight.Strong Bonding: Excellent for repair work as it creates a powerful bond between old and new concrete surfaces.Crack Resistance: Improves flexibility, allowing the concrete to handle minor movements and temperature changes without cracking.Durability: Protects against weathering, corrosion, and chemical damage, increasing the structure's life.Easy Application: Simply add the liquid to your mixing water. No complex steps are required.
Ideal For:Waterproofing terraces, bathrooms, basements, swimming pools, and water tanks.Concrete repair and plastering work.Fixing leaking roofs and walls.Available in: 1 Ltr, 5 Ltr, and 20Ltr containers.
Questions & Answers (Q&A)Q1: What is the exact mixing ratio for a 50kg bag of cement?A: For a 50kg cement bag, use about 2.5 litres of Dr. Fixit 301 URP mixed with 10 litres of water. This replaces all the plain mixing water.Q2: Can I use it on an old, leaking terrace? How?A: Yes. First, remove any loose material and clean the surface. Then, apply a fresh layer of plaster or mortar that has been mixed with Dr. Fixit 301 URP. This will create a strong, waterproof barrier.Q3: Is it safe for drinking water tanks?A: Absolutely. Once the concrete or mortar has fully cured (after 28 days), it is completely non-toxic and safe for potable water.Q4: How is this better than a waterproof paint or coating?A: Paint sits on the surface and can peel or wear off. Dr. Fixit 301 URP waterproofs the entire concrete mix from the inside, making the protection permanent and more reliable.Q5: What is the shelf life?A: The product has a shelf life of 18 months from the date of manufacture if stored in a cool, dry place in its original sealed container.Q6: Are you an authorized dealer?A: Yes, we are an authorized distributor for Dr. Fixit products, ensuring you receive 100% genuine and fresh material.Q7: What are the payment and delivery terms?A: We accept all major online payment modes. We offer pan-India shipping. Delivery cost and time depend on your location and order size. Please message us for a precise quote.

 91 000 74051 Dr. Fixit Fastflex is a two component acrylic cementitious coating system for waterproofing of wet areas and any water retaining structures such as swimming pools and water features. It provides strong bonding and excellent resistant to hydrostatic water pressure by forming highly elastic seamless coating over the applied concrete surfaces.

 91 000 74051 Dr.fixit tape Adhesive 2-Part high performance Epoxy adhesive specially designed for bonding Dr. Fixit Seal Tape series of Expansion joint tapes to different surfaces. It is solvent-free, non-sag, multipurpose bonding agent for suitable for use on horizontal and vertical surfaces.

 91 000 74051  Dr. Fixit Cipoxy 16D is a solventless, medium viscous, epoxy primer. Typical Application Cipoxy 16D is used as primer / sealer in conjunction with epoxy, PU and polyurea coating system.
 Features & Benefits   Ease of application: Easy to mix & apply by brush.  Penetration: Low viscosity penetrates into concrete surfaces.  Excellent Bonding: Bonds strongly to damp concrete surfaces moisture content up to 7% User friendly: Does not blister on curing.  Multipurpose : The most suitable epoxy primer for PU, polyurea and top coats Method of Application

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Roofseal Ultra is an elastomeric polyurethane hybrid next generation liquid applied protective roof waterproofing coating designed to resist water intrusion. The high solids polymers in Dr. Fixit Roofseal Ultra provides weather resistance mechanical properties, long-term durability. Upon curing, forming thick protective totally watertight, highly elastic and durable membrane without seams or joints. The waterproofing membrane is resistant to UV radiation, with high solar –reflectance index 106 and highly resistant to ponding water.

 91 000 74051 Dr. Fixit Roofseal Ultra is an elastomeric polyurethane hybrid next generation liquid applied protective roof waterproofing coating designed to resist water intrusion. The high solids polymers in Dr. Fixit Roofseal Ultra provides weather resistance mechanical properties, long-term durability. Upon curing, forming thick protective totally watertight, highly elastic and durable membrane without seams or joints. The waterproofing membrane is resistant to UV radiation, with high solar –reflectance index 106 and highly resistant to ponding water.

 91 000 74051 Dr. Fixit Flexi PU 270(I) A high-performance, solvent-based, one-component, polyurethane waterproofing membrane. It is liquid-applied, cures upon contact with air moisture, and forms a highly flexible, seamless, and elastic protective layer.
Primary Function: To provide a durable, long-lasting, and root-resistant waterproofing barrier for a wide variety of structures, capable of bridging cracks and withstanding significant structural movement.
Key Features & Benefits (from TDS):
Highly Elastic & Flexible: Exceptional elongation (400%) to bridge cracks up to 2mm and accommodate movement.Seamless Membrane: Forms a continuous, joint-free layer, eliminating weak points.Excellent Adhesion: Bonds strongly to most substrates (concrete, metal, asbestos, etc.).Breathable: Allows water vapour to escape from the structure (permeable).Durable: Resistant to water, frost, chemicals, oils, detergents, and plant roots.Wide Temperature Range: Maintains properties from -40°C to +80°C.Root Resistant: Certified as resistant to plant roots (EN 13948), making it ideal for roof gardens.
Q1: How is this product applied?A: It is typically applied in 2 or 3 coats by roller, brush, or airless spray.Surface Prep: Surface must be clean, sound, and absolutely dry (<5% moisture). New concrete must cure for 28 days.Priming: Absorbent surfaces must be primed with Dr. Fixit Primer PU or Dr. Fixit Pidipoxy MIFP.Application: Apply the first coat. Apply the second coat after 12-18 hours (but within 48 hours).Reinforcement: Reinforce critical areas (corners, joints, pipes) with Geotextile Fabric embedded in the wet coating.Q2: What is the coverage area?A: The total consumption is approximately 1.2 – 1.5 kg per square meter for a 2 or 3-coat system. Actual consumption depends on surface porosity and application method.Q3: How long does it take to cure?A:Tack-free: 5-6 hours (at 20°C, 50% RH)Light foot traffic: 24 hoursFinal cure: 7 daysQ4: Does it need a protective layer?A: Yes, protection is mandatory.For terraces: Protect with a 40-50mm concrete screed (M20 grade) laid over a geotextile separation layer.For roof gardens: Follow the screed with finishing layers (brickbat coba, tiles, etc.).Alternatively, it can be finished with Dr. Fixit PUTC (polyurethane top coat) for UV stability and colour.Q5: Can it be applied on wet surfaces?A: No. Absolutely not. The surface must be completely dry (<5% moisture content). The TDS explicitly warns: "Do not wash surface with water." before application.Q6: What is the shelf life?A: 9 months from the date of manufacture when stored in its original, unopened container in a dry, cool place (5°C to 30°C), protected from moisture and direct sunlight.Q7: Is it safe? What precautions are needed?A: Caution Required. The product contains isocyanates. During application, you must wear:Protective clothingChemical-resistant glovesEye gogglesAvoid contact with skin and eyes. Ensure adequate ventilation. Always refer to the Material Safety Data Sheet (MSDS) before use.Q8: How does it handle cracks?A: It has excellent crack-bridging capabilities:It can bridge dynamic cracks up to 2mm wide.Larger cracks and joints must be pre-sealed with Dr. Fixit PU Sealant and reinforced with geotextile fabric before the general membrane application.

 91 000 74051 Dr. Fixit Pidigrout 10M - High-Strength, Non-Shrink Grout is a ready-to-use, free-flowing cementitious grout that provides very high strength and does not shrink after setting. It is specially designed for heavy-duty applications where a strong, stable, and reliable foundation is critical, such as under heavy machinery, bridge bearings, and structural columns.
Key Benefits:
High Strength: Achieves compressive strength of over 800 ksc (approx. 80 MPa) in 28 days.Non-Shrink: Expands slightly upon setting to ensure a perfect, full-contact bond with the base.Free-Flowing: Easily flows into tight spaces and under base plates without needing vibration.Ready-to-Use: Just add water and mix for easy application.Heavy-Duty: Ideal for machinery foundations, precast structures, and turbine bases.Approximate Market Price: 399 - 499 per 25 kg bag (Please contact for the best bulk price!)
Questions and Answers:Q1: What is Pidigrout 10M used for?A: It is used for grouting applications that require high strength and stability. Common uses include fixing heavy machinery bases, bridge bearing pads, boiler foundations, turbine generator plates, and structural columns.Q2: How much water should be added to a 25kg bag?A: For a free-flowing consistency, add 4.0 to 4.5 liters of clean water per 25kg bag. For a drier, trowelable mix, use 3.25 to 3.5 liters of water. Never add extra water.Q3: What is the coverage or yield from one bag?A: One 25kg bag mixed with water yields approximately 12.5 liters of grout.Q4: What is the approximate price?A: The approximate price for a 25kg bag is 499 TO 518. Contact CIVILIZEMART us for a precise quote, especially for bulk orders.Q5: How strong is this grout?A: It is very high-strength. It achieves over 350 ksc in 24 hours and reaches a final compressive strength of over 800 ksc (80 MPa) in 28 days.Q6: Does it shrink or expand?A: It is a non-shrink grout. It undergoes a slight controlled expansion during setting to compensate for any shrinkage, ensuring a tight, void-free fill under the base plate.Q7: What is the shelf life?A: When stored in a sealed container in a shaded area, it has a shelf life of up to 1 year.Q8: Can it be used for deep fills?A: Yes, for fills deeper than 75mm, you can add approximately 10 kg of clean, washed 10mm crushed aggregates to each 25kg bag of grout to reduce heat generation and cost.Q9: What precautions should be taken during application?A:Soak the base surface with water for 24 hours before grouting.Ensure the shuttering (formwork) is completely leak-proof.Do not add extra water to the mix.Cure the grout after placement by covering it with wet jute bags or using a curing compound.

 91 000 74051 Dr. Fixit Pidigrout 10M - High-Strength, Non-Shrink Grout is a ready-to-use, free-flowing cementitious grout that provides very high strength and does not shrink after setting. It is specially designed for heavy-duty applications where a strong, stable, and reliable foundation is critical, such as under heavy machinery, bridge bearings, and structural columns.
Key Benefits:
High Strength: Achieves compressive strength of over 800 ksc (approx. 80 MPa) in 28 days.Non-Shrink: Expands slightly upon setting to ensure a perfect, full-contact bond with the base.Free-Flowing: Easily flows into tight spaces and under base plates without needing vibration.Ready-to-Use: Just add water and mix for easy application.Heavy-Duty: Ideal for machinery foundations, precast structures, and turbine bases.Approximate Market Price: 399 - 499 per 25 kg bag (Please contact for the best bulk price!)
Questions and Answers:Q1: What is Pidigrout 10M used for?A: It is used for grouting applications that require high strength and stability. Common uses include fixing heavy machinery bases, bridge bearing pads, boiler foundations, turbine generator plates, and structural columns.Q2: How much water should be added to a 25kg bag?A: For a free-flowing consistency, add 4.0 to 4.5 liters of clean water per 25kg bag. For a drier, trowelable mix, use 3.25 to 3.5 liters of water. Never add extra water.Q3: What is the coverage or yield from one bag?A: One 25kg bag mixed with water yields approximately 12.5 liters of grout.Q4: What is the approximate price?A: The approximate price for a 25kg bag is 499 TO 518. Contact CIVILIZEMART us for a precise quote, especially for bulk orders.Q5: How strong is this grout?A: It is very high-strength. It achieves over 350 ksc in 24 hours and reaches a final compressive strength of over 800 ksc (80 MPa) in 28 days.Q6: Does it shrink or expand?A: It is a non-shrink grout. It undergoes a slight controlled expansion during setting to compensate for any shrinkage, ensuring a tight, void-free fill under the base plate.Q7: What is the shelf life?A: When stored in a sealed container in a shaded area, it has a shelf life of up to 1 year.Q8: Can it be used for deep fills?A: Yes, for fills deeper than 75mm, you can add approximately 10 kg of clean, washed 10mm crushed aggregates to each 25kg bag of grout to reduce heat generation and cost.Q9: What precautions should be taken during application?A:Soak the base surface with water for 24 hours before grouting.Ensure the shuttering (formwork) is completely leak-proof.Do not add extra water to the mix.Cure the grout after placement by covering it with wet jute bags or using a curing compound.

 91 000 74051 Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation.

91 000 74051  Dr. Fixit Bathseal Select is a ready-to-use; liquid-applied elastomeric water based waterproof coating. That cures to form a monolithic membrane designed for wet areas under tiled finish application. Being a 1K liquid applied coating, it reduces mixing errors and saves time due to excellent flow properties and thereby easy application with roller or brush. It is fully compatible with polymer modified cement based tiles adhesives, screeds and renders.

 91 000 74051 Dr. Fixit Torchshield Primer is a solvent based bitumen modified primer conforming to ASTM D/41, to be used to seal and prepare the substrate prior to the installation of the Dr. Fixit Torchshield torch-on and Dr. Fixit Samshield, self adhesive membranes. In addition to that, it also acts as a binder for the dust particles which gets accumulated on the concrete surface even after cleaning

 91 000 74051 Dr. Fixit Pidigrout 10M - High-Strength, Non-Shrink Grout is a ready-to-use, free-flowing cementitious grout that provides very high strength and does not shrink after setting. It is specially designed for heavy-duty applications where a strong, stable, and reliable foundation is critical, such as under heavy machinery, bridge bearings, and structural columns.
Key Benefits:
High Strength: Achieves compressive strength of over 800 ksc (approx. 80 MPa) in 28 days.Non-Shrink: Expands slightly upon setting to ensure a perfect, full-contact bond with the base.Free-Flowing: Easily flows into tight spaces and under base plates without needing vibration.Ready-to-Use: Just add water and mix for easy application.Heavy-Duty: Ideal for machinery foundations, precast structures, and turbine bases.Approximate Market Price: 399 - 499 per 25 kg bag (Please contact for the best bulk price!)
Questions and Answers:Q1: What is Pidigrout 10M used for?A: It is used for grouting applications that require high strength and stability. Common uses include fixing heavy machinery bases, bridge bearing pads, boiler foundations, turbine generator plates, and structural columns.Q2: How much water should be added to a 25kg bag?A: For a free-flowing consistency, add 4.0 to 4.5 liters of clean water per 25kg bag. For a drier, trowelable mix, use 3.25 to 3.5 liters of water. Never add extra water.Q3: What is the coverage or yield from one bag?A: One 25kg bag mixed with water yields approximately 12.5 liters of grout.Q4: What is the approximate price?A: The approximate price for a 25kg bag is 499 TO 518. Contact CIVILIZEMART us for a precise quote, especially for bulk orders.Q5: How strong is this grout?A: It is very high-strength. It achieves over 350 ksc in 24 hours and reaches a final compressive strength of over 800 ksc (80 MPa) in 28 days.Q6: Does it shrink or expand?A: It is a non-shrink grout. It undergoes a slight controlled expansion during setting to compensate for any shrinkage, ensuring a tight, void-free fill under the base plate.Q7: What is the shelf life?A: When stored in a sealed container in a shaded area, it has a shelf life of up to 1 year.Q8: Can it be used for deep fills?A: Yes, for fills deeper than 75mm, you can add approximately 10 kg of clean, washed 10mm crushed aggregates to each 25kg bag of grout to reduce heat generation and cost.Q9: What precautions should be taken during application?A:Soak the base surface with water for 24 hours before grouting.Ensure the shuttering (formwork) is completely leak-proof.Do not add extra water to the mix.Cure the grout after placement by covering it with wet jute bags or using a curing compound.

 91 000 74051 Dr. Fixit Dampguard is a two-component coating composed of epoxy resin, curing agent, inert pigments & properly selected fine fillers, additives in water as a medium. It has an advantage of dilution with water for application over cementitious surfaces. It is used as an internal coating for the waterproofing treatments of water tanks and building walls because it can be applied over damp surfaces, has excellent water resistance, adhesion, hardness, toughness and sets faster similar to solvent based epoxy formulations.

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART

 91 000 74051 Dr. Fixit Micro Concrete is a ready to use dual shrinkage compensated dry powder, requiring only the addition of clean water to produce a free flowing dimensionally stable micro concrete.

 91 000 74051 Dr. Fixit Roofseal Classic Grey is a single-component, elastomeric waterproofing coating based on PU-Acrylic hybrid emulsion, reinforced with nano-fibers. Designed to form a seamless flexible membrane that protects roof surfaces from water seepage, heat, UV degradation, and structural micro-movement. Ideal for both new & old roofs, terraces, screeds, tile & mosaic surfaces, and provides a combination of waterproofing and heat insulation benefits.
Q1. Can I use Roofseal Classic Grey over an existing waterproofing layer?Yes, provided the existing layer is sound, clean, free of loose particles, moss/algae removed, and surface properly prepared. Minor cracks should be filled first. Q2. How many coats and how thick should each coat be?Typically two coats. The first coat is applied and allowed to dry (~4-6 hrs), then the second coat perpendicular to the first. Total dry film thickness (DFT) ~450-500 microns. Q3. How soon after application can I expose it to rainfall?Avoid rain for at least 48 hours after application to allow proper setting / curing. Surface temperature should be between ~10-35 °C during application. Q4. Is Roofseal Classic Grey suitable for heavy foot traffic?It is suitable for light foot traffic; for heavy traffic, protective screeds or foot-paths should be added. Q5. What is the approximate price for Gallon / Bucket SKU?For 20 L buckets, price is around Please visit CIVILIZEMART