Civilize Mart

• Colour fastness
• Provides flexibility
• Improves compressive strength
• Reduces water absorption

• Colour fastness
• Provides flexibility
• Improves compressive strength
• Reduces water absorption

•  91 000 74051 This is a cement-based, polymer-modified unsanded grout (not epoxy). 

• Designed for tile/stone joints of width ~ 1 mm to 3 mm — so fairly narrow joints. 

• Works with a variety of surfaces: ceramic tiles, vitrified tiles, glass mosaics, granite, marble and other natural or engineered stones. 

• Comes in multiple packaging sizes (commonly 1 kg or 10 kg) and a wide range of colours (over 30+).

• Smooth, non-scratching finish — since it's unsanded, it’s safer for polished tiles, glass tiles, marble and delicate surfaces where sanded grout could scratch.

• Good adhesion & durability — polymer modification improves strength and bonding compared to plain cement grout. 

• Weather- and water-resistant — suitable for both interior and exterior applications. Colour-fast and uniform — grout retains its colour over time without significant fading. 

• Economical & easy to apply — widely available and a cost-effective option for narrow grout lines. 

Use this grout when:

• Joints between tiles/stones are narrow (1 – 3 mm) — for example, wall tiles, small floor tiles, mosaic, or polished stone surfaces.

• You have delicate or polished tiles (e.g. marble, glass mosaic, vitrified tiles) — unsanded grout reduces risk of scratching.

• You want a smooth, fine finish on tile walls or floors without visible sand particles.

• You need a budget-friendly, versatile grout for regular residential or commercial tiling jobs.

• Because it’s unsanded and meant for narrow joints, it’s not suitable for wider grout joints (> 3 mm) — for those, a sanded grout would be better. As a cement-based grout, it may not offer the same stain-resistance or chemical resistance as high-end epoxy grouts.

• Proper mixing and application is needed (optionally with a grout-admixture for better performance) to achieve good strength and avoid shrinkage/cracking

•  91 000 74051 SP-100 is a 100 % solid epoxy-based grout, not a basic cement-grout. 

• It’s designed for floors and walls — works with ceramic tiles, vitrified tiles, marble/stone, glass mosaic, terrazzo, engineered stone etc.  

• The kit is supplied as a 3-component unit: Hardener (Part A), Resin (Part B) + Coloured Filler Powder (Part C).

• Stain-free & colour-fast — resists staining from dirt, water, cleaning agents, food spills etc. 

• Chemical, water and temperature resistant — good for wet zones, kitchens, bathrooms, even institutional/industrial use. 

• Durable, non-cracking, non-powdering and long-lasting — epoxy doesn’t deteriorate like cement grouts over time. 

• Anti-bacterial and anti-fungal — useful especially in moisture-prone areas to reduce mold/mildew risk. 

• Easy to clean & maintain — smooth, water-cleanable finish. 

• Wide colour options — over 30+ colours available, so you can match grout to tiles. 

SP-100 is especially suitable for:

• Kitchens, bathrooms, washrooms (residential or commercial) — places exposed to frequent spills or moisture. 

• High-traffic floors, commercial spaces, food-service areas, hospitals, swimming-pools, hygienic areas — where durability and stain resistance matter. 

• Areas where tile joints need to stay clean, germ-free, and easy to maintain (e.g. hospitals, kitchens, bathrooms). 

• It is not a waterproof “joint sealant” — it grouts the joints cleanly but doesn’t function as a full waterproof barrier. 

• Because it's epoxy-based, application requires mixing of components and some care — proper mixing and cleaning immediately after application is needed.

• Usually more expensive and slightly more involved to apply than simpler cement-based grouts (but performance is better).

•  91 000 74051 SP-100 DUO is a two-component (epoxy) grout — not a standard cement grout — designed for both floor and wall tile/stone joints.

• It’s made by mixing a hardener (Part A) and a resin (Part B) (plus filler), which cures into a very strong, dense, stain-resistant grout. 

• It meets international standards for epoxy grout — including ANSI A118.3, ISO 13007 / EN 13888. 

• Stain-free & colour-fast — resists stains from spills, residues, cleaning agents; grout lines stay clean long-term. 

• Water-resistant, chemical & temperature-resistant — works well in wet areas (bathrooms, kitchens, poolsides), and resists household chemicals.

• Durable: non-cracking, non-powdering, shock-/abrasion-resistant — suitable for high-traffic areas, floors and walls that see heavy use. 

• Versatile substrate compatibility — can be used with ceramic tiles, vitrified tiles, glass mosaic, marble/stone/natural stone, engineered stone, metal tiles, terrazzo, etc. 

• Hygienic / Food-grade & anti-microbial — good for kitchens, restaurants, hospitals, or other hygiene-sensitive environments. 

• Suitable for both interior and exterior — because it’s UV-resistant and handles temperature variations.

SP-100 DUO is ideal for:

• Kitchens and bathrooms (floors, walls, backsplashes) — where water, moisture, spills are common.

• Wet zones: swimming pools, spas, sauna areas, water bodies — thanks to water-resistance and durability.

• High-traffic floors (entrances, corridors) or commercial/industrial floors (restaurants, hospitals, labs, cafeterias).

• Stone/tile installations on floors or walls — ceramic, vitrified, natural stone, etc.

• Outdoor or semi-outdoor areas — because of its weather/UV resistance.

• SP-100 DUO is a grout — not a waterproofing membrane/sealant. It helps fill and seal joints, but you’ll still need proper waterproofing layer if the surface demands full waterproofing. 

• Because it’s epoxy-based, application needs correct mixing (Parts A + B) and proper cleaning immediately after application. Mistakes during mixing or cleaning can affect finish or performance. 

• It may be more expensive than simple cement-based grouts; but performance, longevity and maintenance savings often justify the cost.

• 91 000 74051 Latapoxy Dazzle is a 100% solid epoxy-based grout (not a basic cement grout), supplied as a 3-component kit (resin, hardener, and coloured filler) — similar to other epoxies from the same manufacturer.It’s designed for floor AND wall tiles, and supports a wide range of substrates: ceramic/vitrified/porcelain tiles, glass mosaics, natural stone (granite, marble), engineered stone, metal tiles, precast terrazzo — basically any standard tile/stone used in interiors or covered exteriors. 

• A distinguishing feature: it offers a “dazzle/metallic finish” — available in three finishes (Gold, Silver, Copper) and multiple colours — so the grout lines can contribute aesthetically, not just functionally.  

• Stain-free and water-resistant: Because it’s epoxy, the grout is non-porous — resistant to stains from water, spills, dirt — ideal for kitchens, bathrooms, wet zones, poolsides, etc. Durable, chemical & temperature resistant: Epoxy grout stands up to chemicals, temperature changes, moisture — good for heavy use areas or places exposed to cleaning agents / harsh conditions. 

• Non-cracking, non-powdering, long-lasting: Unlike cement-based grout that can crack or powder over time, epoxy grout remains stable — lower maintenance and better lifespan. Enhanced aesthetics: The metallic “Dazzle” finish (gold/silver/copper) and multiple colour options allow grout lines to match or complement tile/stone — useful especially in decorative floors, designer tiles, mosaic work, showrooms, etc. 

• Hygienic – anti-fungal & anti-bacterial: Because of non-absorbent and sealed surface, the grout reduces chances of mold, mildew or bacterial growth — beneficial for bathrooms, kitchens, wet zones. 

Use Latapoxy Dazzle when:

• You have ceramic/vitrified tiles, glass mosaic, natural stone or designer/porcelain tiles.

• You want floor + wall tile joints with high durability, water/chemical resistance — e.g. kitchens, bathrooms, lobbies, showrooms, commercial spaces, even pools or wet zones (covered exterior). 

• You care about appearance — especially if tiles are decorative, polished or mosaic; Dazzle’s metallic finish makes grout lines stand out (or blend) aesthetically.

• You want low maintenance + long-lasting grout that won’t stain, crack, or powder easily, and stays hygienic over time.

• Because it is epoxy-based, mixing and application must be done properly (resin + hardener + filler) — mistakes in mixing ratio or application can compromise performance.

• As with all epoxy grouts: it might be slightly more expensive than basic cement-based grout or grout-admixture options — but the trade-off is much better performance and longevity.

•  

• Packaged as a factory-proportioned kit (resin, hardener, filler) — usually in units of 1.25 kg (¼ unit) or 5 kg (full unit) depending on job size. 

• Meets quality standards: ANSI A118.3 and EN 13888 (RG2) — ensuring it aligns with international norms for epoxy grouts. 

 91 000 74051 MYK LATICRETE 9237 is a ready-to-use, liquid rubber waterproofing membrane — roller-applied — that creates a seamless, flexible waterproof barrier. It’s designed for use under ceramic tile, stone and other finishes in both thin-bed and thick-bed installations on floors and walls. 

• Easy application — 9237 applies like paint using a brush or roller. 

• Clean and safe during application — water-cleanable when fresh, non-flammable, generally low in odor. 

• Crack isolation / anti-fracture protection — can bridge non-structural cracks up to ~ 3 mm (1/8″), protecting tile/stone finishing from substrate shrinkage or minor cracks. 

• Strong adhesion to many substrates — effective on concrete, cement mortar beds, cement plaster, cement backer boards, gypsum wallboard, brick or masonry, even exterior-grade plywood (check substrate suitability for exterior use). 

• Versatile use — horizontal & vertical surfaces — suitable for wet areas like bathrooms, kitchens, terraces, balconies, utility rooms; also for exterior or interior applications depending on substrate. 

• Bathrooms, shower areas, washrooms — as a waterproof barrier under tiles/stone. 

• Kitchens, laundries, utility areas or other indoor wet zones. 

• Balconies, terraces, and other semi-exterior spaces (depending on substrate and local guidelines). 

• Under tile or stone finishes over cement mortar beds, backer-boards, concrete, plaster, or masonry — residential or commercial floors/walls. 

• Available in 5 L and 20 L pails

• Coverage: ~ 200–225 sq. ft per 20 L pail (coverage may vary with substrate condition, thickness applied, and application method). 

• Meets recognized standards for waterproofing membranes (e.g. conforming to standards like EN 14891 / similar relevant specs). 

• Substrate must be clean, sound, free of dust, oil, sealers, curing compounds etc. before application for optimal adhesion. 

• In areas with corners, coves, board joints, or changes in plane, it’s recommended to use reinforcing fabric along with the liquid membrane for improved waterproofing integrity. 

• Allow membrane coats to dry sufficiently (per manufacturer instructions) before tiling or further work. Some data sheets note tile/stone can be installed once the membrane is “dry to touch”

•  91 000 74051 PUA 212® is a two component, modified Polyurethane Adhesive designed for the installation of ceramic tile, vitrified tile, metal tile, glass tile, agglomerates, glass mosaic tile and natural stone on any substrate. It is highly elastic, thixotropic and suitable to lay water sensitive tiles & stones on highly expandable, deformable, absorbent and non-absorbent substrates.

•  91 000 74051 DWA 215 is a single-component modified polyurethane adhesive, ready-to-use, made for bonding tiles, vitrified tiles, glass-mosaic tiles, and natural stone to surfaces like cement-based floors, cement mortar beds, plywood boards, drywall (gypsum boards), cement backer boards, AAC block walls, etc. It’s used in both residential and commercial settings (interior and exterior) for tiling jobs where a strong, durable bond is needed under various conditions. 

Key Properties / Why It’s Used

• Single-component and ready to use (no mixing required).

• High bonding strength — suitable for tiles, vitrified tiles, natural stone, mosaics, on a variety of suitable substrates. 

• Works on both cement-based and drywall/wood-based surfaces (provided they are clean, dry, sound) — gives flexibility for different construction substrates. 

• Complies with standards for adhesive strength (ANSI / EN / ISO classification D2TE) — meaning it’s a recognized professional-grade adhesive. 

 91 000 74051 LATICRETE 73 Crete Admix is a liquid latex-based admixture that replaces water when mixing Portland-cement + sand mortars or adhesive powders. When used instead of water, it produces a polymer-fortified mortar or adhesive with superior flexibility, adhesion, and strength compared to conventional cement-sand mortar.

Combined with a compatible cementitious powder (e.g. LATICRETE 111 or 211 series), 73 Crete Admix results in a high-performance tile/stone adhesive or thin-bed mortar, suitable for demanding installations. 

• Stronger bond & better adhesion: Mortars made with 73 Crete Admix bond more strongly to substrates than regular cement-sand mixes — important for secure installations of tiles, vitrified tiles, natural stone, mosaics, etc. 

• Increased flexibility and impact/shock resistance: The polymer-modified mortar can better absorb movement, stresses, thermal expansion/contraction — reducing risk of cracks or de-bonding. Suitable for wet & dry applications, interior & exterior: Works well in bathrooms, kitchens, balconies, terraces, swimming pools, fountains — anywhere tile or stone needs to adhere reliably, even in presence of moisture or water. Non-flammable & easy to use: As a liquid admixture, 73 Crete Admix is non-flammable and replaces water straightforwardly — simplifying mixing and improving reliability of results vs. inconsistent on-site cement-sand mixes. Certified and standards-compliant when used with compatible powder: The system (73 Crete Admix + cement-based powder) meets standards such as EN 12004 “C2 TE” for tile adhesives — 

• 73 Crete Admix is used in place of water when mixing Portland cement + sand mortars or cement-adhesive powders. 

• It’s ideal for producing thin-bed tile adhesives (for ceramic tiles, vitrified tiles, natural stone, mosaics), or polymer-modified mortar beds/adhesives for floors and walls, indoors or outdoors. 

• Works well on a variety of substrates: concrete, cement mortar beds/plasters/ screeds, brick/concrete masonry, cement backer boards, cement renders — depending on substrate suitability. Also suitable for wet areas and submerged applications — such as swimming pools, fountains, balconies, wet-area floors — . 

Using 73 Crete Admix ensures that tile/stone adhesives or mortars supplied by CivilizeMart deliver enhanced adhesion, flexibility, durability and resistance to shocks, moisture, thermal fluctuations or structural movement. For clients demanding long-lasting floors, wet-area tiling (bathrooms, kitchens, pools), or external masonry or facade work 

•  91 000 74051 This is a cement-based, polymer-modified unsanded grout (not epoxy). 

• Designed for tile/stone joints of width ~ 1 mm to 3 mm — so fairly narrow joints. 

• Works with a variety of surfaces: ceramic tiles, vitrified tiles, glass mosaics, granite, marble and other natural or engineered stones. 

• Comes in multiple packaging sizes (commonly 1 kg or 10 kg) and a wide range of colours (over 30+).

• Smooth, non-scratching finish — since it's unsanded, it’s safer for polished tiles, glass tiles, marble and delicate surfaces where sanded grout could scratch.

• Good adhesion & durability — polymer modification improves strength and bonding compared to plain cement grout. 

• Weather- and water-resistant — suitable for both interior and exterior applications. Colour-fast and uniform — grout retains its colour over time without significant fading. 

• Economical & easy to apply — widely available and a cost-effective option for narrow grout lines. 

Use this grout when:

• Joints between tiles/stones are narrow (1 – 3 mm) — for example, wall tiles, small floor tiles, mosaic, or polished stone surfaces.

• You have delicate or polished tiles (e.g. marble, glass mosaic, vitrified tiles) — unsanded grout reduces risk of scratching.

• You want a smooth, fine finish on tile walls or floors without visible sand particles.

• You need a budget-friendly, versatile grout for regular residential or commercial tiling jobs.

• Because it’s unsanded and meant for narrow joints, it’s not suitable for wider grout joints (> 3 mm) — for those, a sanded grout would be better. As a cement-based grout, it may not offer the same stain-resistance or chemical resistance as high-end epoxy grouts.

• Proper mixing and application is needed (optionally with a grout-admixture for better performance) to achieve good strength and avoid shrinkage/cracking

•  91 000 74051 SP-100 DUO is a two-component (epoxy) grout — not a standard cement grout — designed for both floor and wall tile/stone joints.

• It’s made by mixing a hardener (Part A) and a resin (Part B) (plus filler), which cures into a very strong, dense, stain-resistant grout. 

• It meets international standards for epoxy grout — including ANSI A118.3, ISO 13007 / EN 13888. 

• Stain-free & colour-fast — resists stains from spills, residues, cleaning agents; grout lines stay clean long-term. 

• Water-resistant, chemical & temperature-resistant — works well in wet areas (bathrooms, kitchens, poolsides), and resists household chemicals.

• Durable: non-cracking, non-powdering, shock-/abrasion-resistant — suitable for high-traffic areas, floors and walls that see heavy use. 

• Versatile substrate compatibility — can be used with ceramic tiles, vitrified tiles, glass mosaic, marble/stone/natural stone, engineered stone, metal tiles, terrazzo, etc. 

• Hygienic / Food-grade & anti-microbial — good for kitchens, restaurants, hospitals, or other hygiene-sensitive environments. 

• Suitable for both interior and exterior — because it’s UV-resistant and handles temperature variations.

SP-100 DUO is ideal for:

• Kitchens and bathrooms (floors, walls, backsplashes) — where water, moisture, spills are common.

• Wet zones: swimming pools, spas, sauna areas, water bodies — thanks to water-resistance and durability.

• High-traffic floors (entrances, corridors) or commercial/industrial floors (restaurants, hospitals, labs, cafeterias).

• Stone/tile installations on floors or walls — ceramic, vitrified, natural stone, etc.

• Outdoor or semi-outdoor areas — because of its weather/UV resistance.

• SP-100 DUO is a grout — not a waterproofing membrane/sealant. It helps fill and seal joints, but you’ll still need proper waterproofing layer if the surface demands full waterproofing. 

• Because it’s epoxy-based, application needs correct mixing (Parts A + B) and proper cleaning immediately after application. Mistakes during mixing or cleaning can affect finish or performance. 

• It may be more expensive than simple cement-based grouts; but performance, longevity and maintenance savings often justify the cost.

•  91 000 74051 TileFixo Style 2K Epoxy Grout is a two-component epoxy tile grout from UltraTech, designed to fill joints between tiles, marble, stone, vitrified/ceramic/glass mosaic/metal tiles, and engineered/precast surfaces. 

• It belongs to the TileFixo “Style” line — intended for “premium tile & marble joints.” 

• Suitable for both floors and walls (horizontal and vertical surfaces).

• Works for interior and external areas, including wet/water-exposed zones such as kitchens, bathrooms, balconies/terraces, swimming pools, etc. 

• Recommended for joint widths ~ 2 mm to ~ 15 mm, according to product specifications for internal/external usage. 

• Water-proof & stain-resistant — helps prevent seepage, dampness, and staining of grout joints. Chemical, temperature & UV-resistant — suitable for heavy-duty use, even in outdoor or exposed conditions.

• Crack-resistant, durable and low-shrinkage — provides long-lasting, stable grout joints. 

• Easy to clean & hygienic — anti-fungal/anti-bacterial, traffic-resistant, good for kitchens, bathrooms and high-use areas. Offers a uniform colour finish and aesthetic look — helpful when using premium tiles, glass mosaics or natural stones.

• Modern tile / marble installations where grout quality and durability matter (bathrooms, kitchens, balconies, pool sides, terraces, commercial areas)

• Projects where waterproofing, stain resistance, chemical resistance and long life are important — e.g. wet areas, outdoor flooring, heavy-use floors

•  91 000 74051 TileFixo GROUT CG is a single-component, cement-based, pigmented grout designed for filling joints between tiles, natural stones, marble, granite, etc.

• It is part of the “TileFixo” product range from UltraTech — meant for grout/joint-filling (not tile-adhesive) rather than tile bonding. 

• Suitable for joint filling in tiles, marble, granite, natural stone floors and walls. 

• Works for horizontal (floors) and vertical (walls) applications. 

• Max recommended tile-joint width: up to 6 mm × 6 mm. 

• Cement-based + polymer-modified — gives better bonding strength compared to plain grout. Non-shrink, self-curing grout: minimizes shrinkage, ensures consistent finish over time. 

• Reduced water absorption → improved durability, less risk of dampness, seepage through joints.

• Uniform and smooth finish — gives neat grout lines and improved aesthetics after installation. 

• Easy to mix and apply — mix with ~ 27–29 % water by weight, stir 2–3 minutes; apply with putty/spatula and clean with sponge/cloth for finishing. 

• Residential and commercial projects — for standard tiling tasks with ceramic, vitrified, natural stone, marble, or granite.

• Floor and wall tile joints (indoors or mild outdoor exposure), where joint width is moderate (≤ 6 mm).

• Users wanting a reliable cement-based grout that gives clean, durable, and water-resistant joints — without going for epoxy grout.

•  91 000 74051 Powergrout NS1 is a cement-based, high-performance precision grout / structural grout made by UltraTech. It’s a single-component, polymer-enriched, non-shrink, non-expanding grout designed for heavy-duty structural grouting rather than light tile-joint filling. 

Powergrout NS1 is typically used for structural and industrial-grade applications, e.g.:

• Grouting under base plates of machines, heavy equipment foundations, bearing plates, columns, precast concrete elements. Anchoring bolts, dowel rods, heavy railings, or precast beams where load transfer and stability are critical. Repair works on concrete surfaces, potholes, structural void-filling, and other critical structural maintenance tasks. 

• High compressive strength — design strength up to ~ 95–100 MPa at 28 days. Non-shrink and non-expanding — ensures dimensional stability after setting, critical in structural grouting to avoid cracks or settling. Self-compacting / flowable grout — flows easily into gaps and voids without need for vibration.Single-component (ready-mix) — just add water (≈ 16.5–17 % by weight) and mix; simpler than multi-part epoxies. 

• Good bond strength and adhesion to concrete and steel — for stable anchoring and load-bearing. 

• Before grouting: surface must be clean — no oil, dust, laitance; reinforcement/steel surfaces should be clean, dry, and properly treated. Mixing: use mechanical mixer; mix thoroughly to lump-free consistency; let stand ~2 min, remix before pouring. 

• Do not over-water to extend pot life — extra water will reduce strength & bonding. 

• It is self-compacting: no vibration needed; using mechanical vibrators may reduce performance. For external conditions or harsh environment: proper curing (water curing for 3 days) may be needed depending on site. 

•  91 000 74051 POWERGROUT NS2 is a cement-based, polymer-enriched, high-performance precision grout, designed for structural/industrial-grade grouting rather than tile-adhesive or joint-grout tasks. 

• It is available in two variants: Flowable and Normal — to suit different site conditions and grouting requirements. 

POWERGROUT NS2 is meant for heavy-duty, load-bearing or structural applications. Typical uses: 

• Grouting under foundation base plates, heavy machinery foundations/beds

• Use in micro-piles, pile caps, shear-wall bond beams

• Anchoring/anchoring of precast elements, structural columns/posts, bolts/fastenings

• Manufacture of high-strength pavers & blocks, repair of RCC surfaces, concrete paths

• Any situation requiring precision grouting to sustain static/dynamic loads — e.g. industrial installations, structural supports. 

According to its technical data: 

• High compressive strength — design strength up to ~ 80 MPa (some references note up to ~ 95–100 MPa depending on mix & conditions) 

• Non-shrink, non-expanding grout — ensures dimensional stability after setting, no unwanted expansion or shrinkage. 

• Polymer-enriched, single-component — ready-to-mix: no need for additional additives, simplifies mixing/application. Self-compacting / flowable (in Flowable variant) — flows easily into voids/undercuts, no need for mechanical vibration. Good bond strength & durability — bonds well with concrete/steel, suitable for structural anchoring and heavy-load applications. Adaptable mix — can include graded coarse aggregates (up to 12 mm or 20 mm) for larger pours or volume grouting. 

• Water-to-powder ratio: ≈ 14–15% by weight for a standard mix. Yield: ~ 19–20 litres per 40 kg bag (at ~ 15% w/p ratio) 

• Compressive strength: ~ 80 MPa (design strength) under recommended conditions. 

• Standards compliance: Meets ASTM standards (C1107, C940, C190, C469, C348, etc.) and relevant Indian standards

• Mixing & application: Use mechanical mixer for lump-free consistency, pour/pump without external vibration (self-compacting). External vibrations can harm final performance. 

• Surface must be cleaned — free of oil, dust, laitance; reinforcement and metal surfaces should be treated properly before grouting. 

• When using coarse aggregate — follow recommended ratio (e.g. 1 part grout : 0.5 part 12 mm aggregate by weight), to maintain designed strength and consistency. Avoid over-watering or extra water beyond recommended ratio — it can reduce strength and bonding. Do not use mechanical vibration when placing – grout is self-compacting; vibration may segregate the mix and compromise integrity. 

 91 000 74051 MYK LATICRETE HYDRO BAN® is a high-performance, liquid-applied waterproofing and crack-isolation membrane. It’s a single-component, self-curing liquid rubber polymer that forms a flexible, seamless, load-bearing waterproof barrier when applied, without the need for fabric reinforcement even in corners or coves. 

• Thin and seamless — when cured, the membrane is only about 0.5 mm–0.8 mm (0.020"–0.030") thick. 

• Flexible & crack-bridging — offers anti-fracture protection, capable of bridging substrate cracks up to ~3 mm (≈ 1/8"). 

• Fast curing & early flood-testing — under suitable conditions, allows flood testing as early as 24–48 hours after application. 

• Bonds to diverse substrates — adheres directly to concrete, cement plaster/screed, cement mortar beds, cement backer boards, brick masonry, even metal or PVC plumbing fixtures (subject to guidelines)

• Tiles/stones can be installed directly — supports tiling, brickwork or stone finishes directly over the cured membrane without additional layers. 

• Safe & durable — non-flammable, solvent-free, meets recognized waterproofing standards (e.g. ANSI A118.10 / A118.12), and includes antimicrobial protection to resist mold and mildew. 

Hydro BAN is suitable for a wide range of waterproofing needs including: 

• Bathrooms, shower pans and stalls — wet areas in residential or commercial properties. 

• Kitchens, laundries, utility areas — zones prone to moisture or water spillage. 

• Balconies, terraces, decks — exterior or semi-exterior spaces requiring waterproofing over mortar or concrete base. 

• Swimming pools, fountains, water bodies — where reliable waterproofing and crack-isolation are critical. 

• Under tile/stone installations — tile, brick or stone floors/walls built directly over the membrane. 

• Supplied in pails (typical industrial/commercial sizes) as liquid membrane. 

• Coverage roughly 225–250 sq.ft per 20-litre pail (two coats typical, depending on substrate and application). 

• Eliminates need for fabric rolls or sheet membranes — simpler, faster application. 

• Saves time — quick drying, early flood testing enables faster tiling schedule. 

• Provides strong crack-bridging and waterproofing — enhances durability of wet-area installations, reduces risk of leaks or seepage even with minor substrate movement. 

• Versatile — works on many substrates (concrete, mortar, plaster, masonry, etc.), interior or exterior, for residential or commercial jobs. 

 91 000 74051 MYK LATICRETE HYDRO BAN® is a high-performance, liquid-applied waterproofing and crack-isolation membrane. It’s a single-component, self-curing liquid rubber polymer that forms a flexible, seamless, load-bearing waterproof barrier when applied, without the need for fabric reinforcement even in corners or coves. 

• Thin and seamless — when cured, the membrane is only about 0.5 mm–0.8 mm (0.020"–0.030") thick. 

• Flexible & crack-bridging — offers anti-fracture protection, capable of bridging substrate cracks up to ~3 mm (≈ 1/8"). 

• Fast curing & early flood-testing — under suitable conditions, allows flood testing as early as 24–48 hours after application. 

• Bonds to diverse substrates — adheres directly to concrete, cement plaster/screed, cement mortar beds, cement backer boards, brick masonry, even metal or PVC plumbing fixtures (subject to guidelines)

• Tiles/stones can be installed directly — supports tiling, brickwork or stone finishes directly over the cured membrane without additional layers. 

• Safe & durable — non-flammable, solvent-free, meets recognized waterproofing standards (e.g. ANSI A118.10 / A118.12), and includes antimicrobial protection to resist mold and mildew. 

Hydro BAN is suitable for a wide range of waterproofing needs including: 

• Bathrooms, shower pans and stalls — wet areas in residential or commercial properties. 

• Kitchens, laundries, utility areas — zones prone to moisture or water spillage. 

• Balconies, terraces, decks — exterior or semi-exterior spaces requiring waterproofing over mortar or concrete base. 

• Swimming pools, fountains, water bodies — where reliable waterproofing and crack-isolation are critical. 

• Under tile/stone installations — tile, brick or stone floors/walls built directly over the membrane. 

• Supplied in pails (typical industrial/commercial sizes) as liquid membrane. 

• Coverage roughly 225–250 sq.ft per 20-litre pail (two coats typical, depending on substrate and application). 

• Eliminates need for fabric rolls or sheet membranes — simpler, faster application. 

• Saves time — quick drying, early flood testing enables faster tiling schedule. 

• Provides strong crack-bridging and waterproofing — enhances durability of wet-area installations, reduces risk of leaks or seepage even with minor substrate movement. 

• Versatile — works on many substrates (concrete, mortar, plaster, masonry, etc.), interior or exterior, for residential or commercial jobs. 

 91 000 74051 MYK LATICRETE Stellar Grout is a high-performance, stain-resistant, fast-setting, and ultra-durable grout designed for joint filling between ceramic, vitrified, porcelain tiles and natural stones. It offers exceptional color consistency, excellent chemical resistance, and long-lasting performance, making it suitable for both interior and exterior applications.

Stellar Grout features advanced resin technology, delivering smoother application, easier cleaning, and superior stain protection compared to traditional cement-based grouts. It is ideal for areas requiring premium aesthetics, hygiene, and long-term durability.

• Stain-resistant & color consistent

• Fast-set technology

• Superior strength & durability

• Smooth and easy application

• Excellent UV, chemical & water resistance

• Suitable for interior & exterior areas

• Perfect for kitchens, bathrooms, balconies & commercial spaces

• Joint filling for:
  ✔ Ceramic tiles
  ✔ Vitrified tiles
  ✔ Porcelain tiles
  ✔ Natural stones

• Wet areas: bathrooms, wash areas

• Dry areas: living rooms, offices

• Heavy-duty commercial spaces

•  91 000 74051 Powergrout NS3 is a cement-based, polymer-enriched, non-shrink, non-expanding precision grout designed for structural/industrial-grade applications. 

• It belongs to the “Industrial & Precision Grout” line of UltraTech’s building-products range. 

• It comes in two variants: NS3 Flowable and NS3 Normal — allowing flexibility depending on site needs.

Powergrout NS3 is suited for structural and medium-heavy grouting jobs such as: 

• Grouting micropiles, pile caps, shear-wall bond beams. 

• Fixing and anchoring precast elements, fasteners, rails, structural anchors. Manufacturing high-strength pavers & blocks, and concrete repairs where a strong binder and grout is required. 

• High early & compressive strength — design strength ~ 55–60 MPa (flowable variant) under recommended conditions. 

• Non-shrink and non-expanding — ensures stable, reliable grouting without cracks or voids. 

• Self-compacting / Flowable (in flowable variant) — flows into gaps/voids without need for vibration, making placement easier.

• Single-component, ready to mix and use — no need for multiple additives or complex mixing; reduces on-site hassle.

• Good bond strength & durability — ensures stable anchoring and long-term performance under load.

• Economical for high-volume applications — coarse aggregates (e.g. up to 12 mm–20 mm) can be added (in recommended ratio) when larger volumes are needed. 

• Surface must be clean — free from dust, oil, laitance, bond-inhibiting agents before grouting.

• Mixed grout should not be over-watered; adding more water than recommended reduces strength and compromises bond. 

• Do not use mechanical vibration when placing — because grout is self-compacting; vibration may lead to segregation and weakness. For external or exposed applications: may require proper curing, depending on ambient conditions. 

 91 000 74051 Epoxy grout is a high-performance grout made from epoxy resins and fillers. Unlike cement grout, epoxy grout is waterproof, stain-resistant, chemical-resistant, and extremely durable.
It’s widely used where moisture, heavy traffic, or chemicals are a concern.

✅ 100% waterproof
✅ No cracking or shrinkage
✅ Resistant to mildew, mold, chemicals
✅ Excellent for wet areas
✅ Strong adhesion & long life

✔ Bathrooms & toilets
✔ Kitchen walls & floors
✔ Swimming pools & water features
✔ Balconies & terraces
✔ Wet areas in commercial spaces
✔ Laboratories & hospitals

1. Standard Epoxy Grout
   — For tiles on walls and floors

2. Chemical-Resistant Epoxy Grout
   — For industrial areas, labs

3. Joint Width-Specific Formulas
   — Narrow joints vs wide joints

• Dr. Fixit Epoxy Grout – Waterproof, stain-resistant, ideal for bathrooms & kitchens

• Dr. Fixit Epoxy Tile Grout – Suitable for larger tiles

• MYK Laticrete SpectraLOCK Pro – High-strength epoxy grout

• MYK Epoxy Grout – Waterproof & chemical resistant

• Ardex Endura Epoxy Grout – Excellent bonding + waterproof performance

• Fosroc Nitoflor FC – Epoxy based floor grout with waterproof properties

• NCL Epoxy Grout – Waterproof & easy application

• UltraTech Epoxy Grout – For indoor wet areas

✔ Clean joints thoroughly before grouting
✔ Mix epoxy grout as per manufacturer’s instructions
✔ Work quickly — epoxy sets fast
✔ Wipe off excess before it hardens
✔ Seal edges where needed

•  91 000 74051 It’s a high-performance three-part epoxy tile adhesive and grout (adhesive + grout in one). 

• Designed for special/advanced use cases: metal, fiberglass (GRP/FRP), impervious surfaces (e.g. metal, coated sheets), moisture-sensitive natural stones and agglomerates, or surfaces that water-based adhesives can’t bond well to.

• Once applied and cured it offers strong bond strength, chemical resistance, water-impermeability, and durability under mechanical stress or vibration — making it suitable even for submerged or wet conditions (e.g. pools, humid areas, bathrooms, possibly outdoor wet surfaces)

• The adhesive supports tile joint width 2–10 mm. For grouting, wait until it hardens (typically ~8 hours under standard conditions) before grouting. 

You’d pick WA 91 when you have:

• Tiles or stones on non-traditional substrates: metal, fiberglass, existing tiles, cement-board, plasterboard, or moisture-sensitive natural stones. 

• Wet areas, chemically-exposed areas, or areas needing high durability — e.g. pool linings, bathrooms, kitchens, industrial/commercial floors, places subject to moisture or chemicals. Vertical walls or situations where “non-slump” adhesive is needed so tiles don’t slide down before curing. 

• It’s a 3-part system: Part A (resin), Part B (hardener liquid), Part C (powder) — all three must be properly mixed.

• Density ~ 1.61 g/cm³ when mixed. Pot life ≈ 45 minutes, open/adjustable time ~ 20-25 minutes. 

• Setting/hardening time: ~24 hours (but grout joints can be done in ~8 hours under typical room conditions). 

• Mechanical strengths are high — e.g. compressive strength ~ 60 N/mm².

• Water absorption: nil (so it remains waterproof once cured). 

Pros:

• Excellent bond and adhesion on difficult or non-porous surfaces.

• Very water- and chemical-resistant — good for wet, industrial, or high-usage areas.

• Can be used for both floor and wall tiles.

• Once applied properly, highly durable and long-lasting.

Things to Note:

• Needs careful mixing (3-part system). Incorrect mixing can compromise adhesion.

• Pot life and working time are limited — must work relatively fast.

• Surfaces must be properly prepared (clean, dry, no dust/grease, etc.) for good adhesion. 

• Slightly more “technical”/“professional-level” than simple cementitious tile adhesives — more suited for projects with challenging substrates or high demands.

•  91 000 74051 TileFixo Rapid is a two-component, epoxy-based tile adhesive in the overall TileFixo line.  

• According to its spec sheet, it complies with standards: IS 15477-2019 (Type 5TS2) and EN 12004 / ISO 13007-1 (R2T) for tile adhesives. 

• It is built for high performance and high strength bonding, suitable for a wide variety of tiles/stones and many different substrates.or

TileFixo Rapid is versatile in terms of tile types and surfaces:

• Suitable for all types of tiles and natural stones — ceramic, vitrified, porcelain, stone, glass-based tiles, etc. 

• Can be used on floors, walls, ceilings, vertical surfaces, overhead surfaces, not only traditional cement-based substrates. 

• Substrate range is broader than cement-only adhesives — works on cementitious surfaces, metals, wood/plywood, existing tiles or stones, drywall, PU/epoxy surfaces, etc. 

• Suitable for both interior and approved exterior applications.

Because of this flexibility, TileFixo Rapid is often chosen when you need a strong, reliable bond on non-standard surfaces (like wood, metal, old tiles), or when you want quick setting / fast installation (for vertical, overhead or difficult-to-handle surfaces).

• Epoxy-based, two-component system — gives much stronger adhesion than standard cement-based adhesives. 

• High bond strength — suitable for heavy tiles and natural stones, even on challenging substrates (metal, old tiles, wood, plasterboard, etc.). 

• Quick-setting / rapid bonding — because of epoxy chemistry and two-component design, ideal for jobs where you want tiles fixed quickly or need early load-bearing.

• Slip-resistant and non-sag — good for vertical or overhead tiling where you don’t want tiles to slide before adhesive cures. 

• Wide substrate compatibility — unlike traditional adhesives limited to cement/plaster/concrete, this works on many substrate types (wood, metal, drywall, existing tiles, etc.). 

• Versatile tile compatibility — from ceramic/vitrified/porcelain to stone and even glass mosaic, giving flexibility in material choice. 

Use TileFixo Rapid when:

• You are tiling on non-cement substrates — e.g. wood/plywood floors, metal surfaces, existing tiles, drywall, PU/epoxy floors, etc.

• You have heavy tiles, natural stone slabs, or irregular or large tiles where strong bond and good adhesion is critical.

• The application is vertical or overhead (like wall tiling, tiling on ceiling, or vertical cladding) — the non-sag and slip-resistant property helps.

• You want fast setting / quick tile-fixing — useful in projects where time is constrained or multiple trades need to follow soon after tiling.

• You need reliable adhesion in interior or approved exterior zones (as per the product guidance).

• Since TileFixo Rapid is two-component and epoxy-based, application needs care — proper mixing of the two components is required. Simply mixing with water as in cement-based adhesives won’t work. 

• For floor areas, full thin-bed application is mandatory — cannot be used like a thick-bed mortar. 

•  

•  91 000 74051 SP-100 DUO is a two-component (epoxy) grout — not a standard cement grout — designed for both floor and wall tile/stone joints.

• It’s made by mixing a hardener (Part A) and a resin (Part B) (plus filler), which cures into a very strong, dense, stain-resistant grout. 

• It meets international standards for epoxy grout — including ANSI A118.3, ISO 13007 / EN 13888. 

• Stain-free & colour-fast — resists stains from spills, residues, cleaning agents; grout lines stay clean long-term. 

• Water-resistant, chemical & temperature-resistant — works well in wet areas (bathrooms, kitchens, poolsides), and resists household chemicals.

• Durable: non-cracking, non-powdering, shock-/abrasion-resistant — suitable for high-traffic areas, floors and walls that see heavy use. 

• Versatile substrate compatibility — can be used with ceramic tiles, vitrified tiles, glass mosaic, marble/stone/natural stone, engineered stone, metal tiles, terrazzo, etc. 

• Hygienic / Food-grade & anti-microbial — good for kitchens, restaurants, hospitals, or other hygiene-sensitive environments. 

• Suitable for both interior and exterior — because it’s UV-resistant and handles temperature variations.

SP-100 DUO is ideal for:

• Kitchens and bathrooms (floors, walls, backsplashes) — where water, moisture, spills are common.

• Wet zones: swimming pools, spas, sauna areas, water bodies — thanks to water-resistance and durability.

• High-traffic floors (entrances, corridors) or commercial/industrial floors (restaurants, hospitals, labs, cafeterias).

• Stone/tile installations on floors or walls — ceramic, vitrified, natural stone, etc.

• Outdoor or semi-outdoor areas — because of its weather/UV resistance.

• SP-100 DUO is a grout — not a waterproofing membrane/sealant. It helps fill and seal joints, but you’ll still need proper waterproofing layer if the surface demands full waterproofing. 

• Because it’s epoxy-based, application needs correct mixing (Parts A + B) and proper cleaning immediately after application. Mistakes during mixing or cleaning can affect finish or performance. 

• It may be more expensive than simple cement-based grouts; but performance, longevity and maintenance savings often justify the cost.

 91 000 74051 Epoxy grout is a high-performance grout made from epoxy resins and fillers. Unlike cement grout, epoxy grout is waterproof, stain-resistant, chemical-resistant, and extremely durable.
It’s widely used where moisture, heavy traffic, or chemicals are a concern.

✅ 100% waterproof
✅ No cracking or shrinkage
✅ Resistant to mildew, mold, chemicals
✅ Excellent for wet areas
✅ Strong adhesion & long life

✔ Bathrooms & toilets
✔ Kitchen walls & floors
✔ Swimming pools & water features
✔ Balconies & terraces
✔ Wet areas in commercial spaces
✔ Laboratories & hospitals

1. Standard Epoxy Grout
   — For tiles on walls and floors

2. Chemical-Resistant Epoxy Grout
   — For industrial areas, labs

3. Joint Width-Specific Formulas
   — Narrow joints vs wide joints

• Dr. Fixit Epoxy Grout – Waterproof, stain-resistant, ideal for bathrooms & kitchens

• Dr. Fixit Epoxy Tile Grout – Suitable for larger tiles

• MYK Laticrete SpectraLOCK Pro – High-strength epoxy grout

• MYK Epoxy Grout – Waterproof & chemical resistant

• Ardex Endura Epoxy Grout – Excellent bonding + waterproof performance

• Fosroc Nitoflor FC – Epoxy based floor grout with waterproof properties

• NCL Epoxy Grout – Waterproof & easy application

• UltraTech Epoxy Grout – For indoor wet areas

✔ Clean joints thoroughly before grouting
✔ Mix epoxy grout as per manufacturer’s instructions
✔ Work quickly — epoxy sets fast
✔ Wipe off excess before it hardens
✔ Seal edges where needed

 91 000 74051 MYK LATICRETE Super Set IWP is a single-component integral waterproofing compound specially formulated to reduce water permeability, improve workability, and enhance the durability of cement mortar, plaster, and concrete. It contains advanced additives that help minimize shrinkage, reduce cracking, and increase compressive strength, making it highly effective for both structural and non-structural waterproofing applications.

The product works internally within the cement matrix, reducing porosity, controlling capillary action, and providing improved waterproofing performance. It conforms to IS 2645:2003, ensuring reliable protection against moisture penetration in wet and exposed areas.

• Reduces permeability of cement mixes

• Improves workability and reduces water demand

• Minimizes shrinkage and cracks

• Enhances compressive strength

• Corrosion-resistant

• Very low chloride content

• Increases durability of concrete and plaster

• Roof concrete

• Screeds

• Water tanks & retaining structures

• Bathrooms & balconies

• Cement plastering

• Sumps, drains, wet areas

• Heavy duty Industrial Grout
• Superior Chemical & Heat Resistance
• Water Cleanable & Fast Curing
• Highly resistant to bacteria and fungi attack

• When the tiles have set firm, spacers and bottom support can be removed
• Before grouting, remove all dust & impurities from the tiles. Dampen the tiled surface with a sponge
• Pour the contents of Part A & Part B into a pail and mix together for 1 min
• Add the part C filler powder ¾ of the content and mix together. Add remaining filler powder if required to achieve desired consistency
• Fill the joints using a rubber float
• Remove the excess grout, holding the float diagonally
• After 30-45 min of the application of the grout scrub the surface of the tile & joint with clean water and scrubber provided to remove any excess grout
• Draw a clean cloth and drag across the tile to remove any residue
• Next day clean the grout haze from the tile with clean water

• Existing joints in concrete must be carried through tile work and shall confirm to architectural details
• Interior installations shall have movement joint spaced a maximum of 10m X 10m. For exterior areas it shall be spaced at 5m X 5m and shall confirm to architectural details
• Follow the Tile Council of America detail EJ-171 Expansion joint

 91 000 74051 MYK LATICRETE Super Set IWP is a single-component integral waterproofing compound specially formulated to reduce water permeability, improve workability, and enhance the durability of cement mortar, plaster, and concrete. It contains advanced additives that help minimize shrinkage, reduce cracking, and increase compressive strength, making it highly effective for both structural and non-structural waterproofing applications.

The product works internally within the cement matrix, reducing porosity, controlling capillary action, and providing improved waterproofing performance. It conforms to IS 2645:2003, ensuring reliable protection against moisture penetration in wet and exposed areas.

• Reduces permeability of cement mixes

• Improves workability and reduces water demand

• Minimizes shrinkage and cracks

• Enhances compressive strength

• Corrosion-resistant

• Very low chloride content

• Increases durability of concrete and plaster

• Roof concrete

• Screeds

• Water tanks & retaining structures

• Bathrooms & balconies

• Cement plastering

• Sumps, drains, wet areas