Civilize Mart

Conbextra GP2 is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free flowing, non-shrink grout for gap thicknesses up to 100mm.
Conbextra GP2 is a blend of Portland cement, graded fillers and chemical additives which impart controlled expansion in the plastic state whilst minimising water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout.
Free flow, high strength, non-shrink, cementitious precision grout

Cebex 100, a plasticised expanding grout admixture is supplied as a powder. The material is a combination of a plasticising agent and a gas producing expansion medium. The plastisicing agent allows the use of a reduced water/cement ratio with consequent increased strengths and durability. The expansive medium counteracts the natural settlement and plastic shrinkage of the grout and aids stability and cohesion.

Lokfix is produced in two versions. The two versions of Lokfixare all pre-measured, two part, filled polyester resin grouts.After hardening, the grout produces anchorages of consistentreproducible values. The versions are:Lokfix S - used where hole diameter is less than 25 mmgreater than the bar diameter.Lokfix P - used in overhead or horizontal holes where bar/holerelationship conforms to Lokfix S. The thixotropic nature ofLokfix P reduces flow of grout out of the hole

 91 000 74051 Fosroc Renderoc Plug is a rapid-setting, cement-based plugging mortar specially designed for stopping water leakages instantly in concrete and masonry structures. It forms a strong, durable, and watertight seal within minutes.
✔ Fast setting – stops running water in 1–2 minutes✔ Non-shrink, chloride-free, safe for concrete✔ High adhesion to damp/wet surfaces✔ Easy to apply – just mix with water and press into the leak✔ Durable waterproof sealing
Applications:
Instant water leak plugging in basements, lift pits, tunnels
Sealing leaks in water tanks, overhead tanks, and reservoirs
Emergency leakage repair in dams, canals, and culverts
Waterproofing for concrete & masonry structures
Packaging: 1 kg, 5 kg, and 15 kg packs

Q1. What is Fosroc Renderoc Plug used for?�� It is used for instant stopping of water leakages in concrete and masonry structures.
Q2. How fast does it set?�� It sets in about 1–2 minutes, depending on water temperature.
Q3. Can it be applied on wet surfaces?�� Yes, it bonds well to wet and damp surfaces.
Q4. Is it suitable for drinking water tanks?�� Yes, it is chloride-free and non-toxic, making it safe for potable water structures.
Q5. What is the method of application?�� Mix the powder with water into a stiff paste and press into the leaking point by hand until set.
Q6. What pack sizes are available?�� 1 kg, 5 kg, and 15 kg packs.
Q7. What is the shelf life?�� 12 months in sealed bags, stored in a dry place.

Q8. What is the price of Fosroc Renderoc Plug?�� Market price usually ranges between ₹350–₹450 per 1 kg pack, depending on location and supplier. Larger packs (5 kg / 15 kg) are available at discounted rates. Contact Civilize Mart for the latest wholesale and retail price.

Renderoc RG is supplied as a ready to use blend of dry powders which requires only the site addition of clean water toproduce a free-fl owing non-shrink repair micro concrete. Thematerial is based on Portland cements, graded aggregatesand fi llers, and additives which impart controlled expansioncharacteristics in the plastic state, while minimising water demand. The low water requirement ensures high early strengthand long-term durability.For larger repairs, the mixed Renderoc RG may be modifi ed bythe addition of 5mm to 12mm clean, graded, saturated surfacedry aggregates at site. For exceptionally large repairs, thelocal Fosroc offi ce shall be consulted.

 91 000 74051 Brushbond RFX - Elastomeric Cementitious Waterproof Coating (Two-Component) (powder + liquid) waterproof coating that is applied by brush or trowel. It creates a flexible, seamless barrier that protects concrete and masonry structures from water, weather, chemicals, and corrosion. It is ideal for water tanks, reservoirs, basements, roofs, and structures in coastal areas. The coating is non-toxic, making it safe for potable water tanks.
Key Benefits:
Flexible & Waterproof: Bridges cracks up to 1mm and is suitable for water-retaining structures.Corrosion Protection: Excellent barrier against chloride ions, carbon dioxide, and sulphates, protecting steel reinforcement.Breathable: Allows water vapour to escape, preventing blistering.UV & Weather Resistant: Durable in all climates, including coastal environments.Non-Toxic: Safe for use in drinking water tanks.
Easy Application: Can be applied by brush, roller, or trowel.
Approximate Market Price: ₹1650 - ₹2123.41 per PACK (for 1mm thickness). Please contact CIVILIZEMART for package pricing!
Questions and Answers:Q1: What is Brushbond RFX used for?A: It is used for waterproofing and protecting concrete structures like water tanks, reservoirs, basements, drainage culverts, and roofs. It is especially good for coastal buildings as it protects against salt and weather damage.Q2: How is it applied?A: It is a two-part system. You mix the powder with the liquid polymer (Nitobond BBX) and water. The mixed paste is then applied like paint using a stiff brush or roller in two coats to achieve a 1mm thickness.Q3: What is the coverage area?A: A standard 15kg + 4.8L pack covers approximately 12-14 square meters at a 1mm thickness. A smaller 5kg + 1.63L pack covers about 4-4.5 square meters.Q4: What is the approximate price?A: The price is typically calculated per square meter. The approximate cost is 1650 to 2123.41 per sq. ft. (for 1mm thickness). Contact CIVILIZEMART us for the exact price of the 15kg and 5kg packs.Q5: Can it be used on drinking water tanks?A: Yes, a key advantage of Brushbond RFX is that it is non-toxic and is ideal for waterproofing potable (drinking) water tanks and reservoirs.Q6: How does it handle cracks?A: The coating is flexible and can bridge static cracks up to 1mm wide, preventing water from seeping through.Q7: What is the shelf life?A: It has a shelf life of 9 months from the date of manufacture when stored in a cool, dry place in its original, unopened packaging.Q8: Is special surface preparation needed?A: The surface must be clean, sound, and free from oil, dirt, or loose material. Light preparation like wire brushing or water jetting is usually sufficient. Large holes or cracks should be repaired first.Q9: How long does it take to dry?A: At normal temperatures (around 27°C), the first coat becomes touch-dry in 4-6 hours, after which the second coat can be applied. The mixed material has a pot life of about 30 minutes.

 91 000 74051 Fosroc Renderoc Plug is a rapid-setting, cement-based plugging mortar specially designed for stopping water leakages instantly in concrete and masonry structures. It forms a strong, durable, and watertight seal within minutes.
✔ Fast setting – stops running water in 1–2 minutes✔ Non-shrink, chloride-free, safe for concrete✔ High adhesion to damp/wet surfaces✔ Easy to apply – just mix with water and press into the leak✔ Durable waterproof sealing
Applications:
Instant water leak plugging in basements, lift pits, tunnels
Sealing leaks in water tanks, overhead tanks, and reservoirs
Emergency leakage repair in dams, canals, and culverts
Waterproofing for concrete & masonry structures
Packaging: 1 kg, 5 kg, and 15 kg packs

Q1. What is Fosroc Renderoc Plug used for?�� It is used for instant stopping of water leakages in concrete and masonry structures.
Q2. How fast does it set?�� It sets in about 1–2 minutes, depending on water temperature.
Q3. Can it be applied on wet surfaces?�� Yes, it bonds well to wet and damp surfaces.
Q4. Is it suitable for drinking water tanks?�� Yes, it is chloride-free and non-toxic, making it safe for potable water structures.
Q5. What is the method of application?�� Mix the powder with water into a stiff paste and press into the leaking point by hand until set.
Q6. What pack sizes are available?�� 1 kg, 5 kg, and 15 kg packs.
Q7. What is the shelf life?�� 12 months in sealed bags, stored in a dry place.

Q8. What is the price of Fosroc Renderoc Plug?�� Market price usually ranges between ₹350–₹450 per 1 kg pack, depending on location and supplier. Larger packs (5 kg / 15 kg) are available at discounted rates. Contact Civilize Mart for the latest wholesale and retail price.

91 000 74051 Complast WL Xtra - Integral Waterproofing Liquid Admixture  is a high-quality, dark brown liquid you mix directly into concrete, plaster, or mortar. It makes your structures permanently waterproof from the inside, reducing leaks and dampness. It's perfect for roofs, bathrooms, water tanks, basements, and external walls. This admixture makes concrete stronger, more durable, and easier to work with.
Key Benefits:Excellent Waterproofing: Drastically reduces water seepage in concrete.Increases Strength: Enhances the compressive strength and durability of concrete.Easy to Use: Liquid formula mixes evenly with water for consistent results.Corrosion Resistant: Protects the steel reinforcement inside the concrete.Standard Compliant: Meets Indian Standard IS:2645-2003.Approximate Market Price: 1500 - 2200 per BUCKET(20L) (Price varies based on quantity. Please contact CIVILIZEMART  for the best quote!)
Questions and Answers Q1: What is Complast WL Xtra used for?A: It is used to make concrete, plaster, and cement mortars waterproof. Common applications include terrace waterproofing, bathroom floors, water tanks, basement walls, and external plastering to prevent water leakage.Q2: How do I use this product?A: It's simple. First, mix your cement and aggregates dry. Then, add most of your mixing water. Finally, mix the required dosage of Complast WL Xtra with the remaining water and add it to the mixer. Mix for another 2 minutes, and your waterproof concrete is ready.Q3: What is the dosage per bag of cement?A: The standard dosage is 200 ml for every 50 kg bag of cement. We recommend doing a small trial mix on-site to confirm the exact dosage for your specific materials.Q4: What is the approximate price?A: The approximate market price is around 1500 to 2200 per liter. The final price depends on the order quantity (e.g., drum, bucket). Please message us for the exact, most competitive price.Q5: Can I use it with any cement?A: Yes, it is compatible with all common types of cement (OPC, PPC, PSC). However, it should not be used with High Alumina Cement.Q6: Does it affect the strength of the concrete?A: No, it maintains and can even increase the compressive strength of concrete because it allows you to use less water while maintaining workability.Q7: What are the available pack sizes?A: It is available in a wide range of sizes for your convenience: 200ml, 1L, 5L, 10L, 20L, 50L, and 200L containers.Q8: Is it safe to handle?A: Yes, it is non-toxic and non-flammable. If it splashes on your skin, wash it off with water. If it gets into your eyes, rinse thoroughly with plenty of water and seek medical attention.Q9: What is the shelf life?A: It has a shelf life of 24 months (2 years) when stored in a cool, dry place in its original, unopened container.

 91 000 74051 Fosroc Renderoc Plug is a rapid-setting, cement-based plugging mortar specially designed for stopping water leakages instantly in concrete and masonry structures. It forms a strong, durable, and watertight seal within minutes.
✔ Fast setting – stops running water in 1–2 minutes✔ Non-shrink, chloride-free, safe for concrete✔ High adhesion to damp/wet surfaces✔ Easy to apply – just mix with water and press into the leak✔ Durable waterproof sealing
Applications:
Instant water leak plugging in basements, lift pits, tunnels
Sealing leaks in water tanks, overhead tanks, and reservoirs
Emergency leakage repair in dams, canals, and culverts
Waterproofing for concrete & masonry structures
Packaging: 1 kg, 5 kg, and 15 kg packs

Q1. What is Fosroc Renderoc Plug used for?�� It is used for instant stopping of water leakages in concrete and masonry structures.
Q2. How fast does it set?�� It sets in about 1–2 minutes, depending on water temperature.
Q3. Can it be applied on wet surfaces?�� Yes, it bonds well to wet and damp surfaces.
Q4. Is it suitable for drinking water tanks?�� Yes, it is chloride-free and non-toxic, making it safe for potable water structures.
Q5. What is the method of application?�� Mix the powder with water into a stiff paste and press into the leaking point by hand until set.
Q6. What pack sizes are available?�� 1 kg, 5 kg, and 15 kg packs.
Q7. What is the shelf life?�� 12 months in sealed bags, stored in a dry place.

Q8. What is the price of Fosroc Renderoc Plug?�� Market price usually ranges between ₹350–₹450 per 1 kg pack, depending on location and supplier. Larger packs (5 kg / 15 kg) are available at discounted rates. Contact Civilize Mart for the latest wholesale and retail price.

91 000 74051 Nitocote Wallguard is water based polymer coating composed of high quality acrylic polymer, with weather resistant pigments, properly selected & graded fine fillers. It is used as a waterproofing & decorative coating for protection of exterior walls of the buildings from heavy wind driven rain.

 91 000 74051 Fosroc Renderoc Plug is a rapid-setting, cement-based plugging mortar specially designed for stopping water leakages instantly in concrete and masonry structures. It forms a strong, durable, and watertight seal within minutes.
✔ Fast setting – stops running water in 1–2 minutes✔ Non-shrink, chloride-free, safe for concrete✔ High adhesion to damp/wet surfaces✔ Easy to apply – just mix with water and press into the leak✔ Durable waterproof sealing
Applications:
Instant water leak plugging in basements, lift pits, tunnels
Sealing leaks in water tanks, overhead tanks, and reservoirs
Emergency leakage repair in dams, canals, and culverts
Waterproofing for concrete & masonry structures
Packaging: 1 kg, 5 kg, and 15 kg packs

Q1. What is Fosroc Renderoc Plug used for?�� It is used for instant stopping of water leakages in concrete and masonry structures.
Q2. How fast does it set?�� It sets in about 1–2 minutes, depending on water temperature.
Q3. Can it be applied on wet surfaces?�� Yes, it bonds well to wet and damp surfaces.
Q4. Is it suitable for drinking water tanks?�� Yes, it is chloride-free and non-toxic, making it safe for potable water structures.
Q5. What is the method of application?�� Mix the powder with water into a stiff paste and press into the leaking point by hand until set.
Q6. What pack sizes are available?�� 1 kg, 5 kg, and 15 kg packs.
Q7. What is the shelf life?�� 12 months in sealed bags, stored in a dry place.

Q8. What is the price of Fosroc Renderoc Plug?�� Market price usually ranges between ₹350–₹450 per 1 kg pack, depending on location and supplier. Larger packs (5 kg / 15 kg) are available at discounted rates. Contact Civilize Mart for the latest wholesale and retail price.

Conplast WL is a dark brown liquid based on lignosulphonateswhich mixes readily with water and therefore disperses evenly.Conplast WL waterproofs by improving the quality of theconcrete or mortar. It reduces the water demand for requiredworkability and minimises segregation and bleeding. Thus it ismore effi cient compared to traditional powder waterproofers asits use results in two fold improvement of concrete or mortar

Nitobond EP is based on solvent-free epoxy resins containingpigments and fine fillers. It is supplied as a two-componentmaterial in pre-weighed quantities ready for on-site mixing anduse. The ‘base’ component is white and the ‘hardener’ componentis black, providing visual evidence (uniform grey colour) thatadequate mixing has been achieved.

cures by reaction with atmospheric moisture to form a tough, elastomeric, waterproof membrane. Nitoproof 600PF is  designed for use on horizontal and vertical surfaces, covered by a protective screed or render

Nitoseal PU40 is a one part, low modulus gun grade elastomericsealant based on polyurethane technology. Nitoseal PU40 maybe applied to joints between 5 and 35mm wide. To minimisestress imposed on the joint sealant, all moving joints shouldbe designed to an optimum width to depth ratio of 2:1 with anoverriding minimum depth of 5mm for non-porous surfaces and10mm for porous surfaces.For joint widths exceeding 35mm, please contact your localFosroc Technical Service Department.

Nitocote Wallguard is water based polymer coating composed of high quality acrylic polymer, with weather resistant pigments, properly selected & graded fine fillers. It is used as a waterproofing & decorative coating for protection of exterior walls of the buildings from heavy wind driven rain.

Renderoc SP40 is supplied as a single component, ready touse blend of dry powders and fi bres which requires only theaddition of clean water to produce a highly consistent, handand spray grade, repair mortar suitable for most structural andload bearing repairs.

 91 000 74051 Brushbond RFX - Elastomeric Cementitious Waterproof Coating (Two-Component) (powder + liquid) waterproof coating that is applied by brush or trowel. It creates a flexible, seamless barrier that protects concrete and masonry structures from water, weather, chemicals, and corrosion. It is ideal for water tanks, reservoirs, basements, roofs, and structures in coastal areas. The coating is non-toxic, making it safe for potable water tanks.
Key Benefits:
Flexible & Waterproof: Bridges cracks up to 1mm and is suitable for water-retaining structures.Corrosion Protection: Excellent barrier against chloride ions, carbon dioxide, and sulphates, protecting steel reinforcement.Breathable: Allows water vapour to escape, preventing blistering.UV & Weather Resistant: Durable in all climates, including coastal environments.Non-Toxic: Safe for use in drinking water tanks.
Easy Application: Can be applied by brush, roller, or trowel.
Approximate Market Price: ₹1650 - ₹2123.41 per PACK (for 1mm thickness). Please contact CIVILIZEMART for package pricing!
Questions and Answers:Q1: What is Brushbond RFX used for?A: It is used for waterproofing and protecting concrete structures like water tanks, reservoirs, basements, drainage culverts, and roofs. It is especially good for coastal buildings as it protects against salt and weather damage.Q2: How is it applied?A: It is a two-part system. You mix the powder with the liquid polymer (Nitobond BBX) and water. The mixed paste is then applied like paint using a stiff brush or roller in two coats to achieve a 1mm thickness.Q3: What is the coverage area?A: A standard 15kg + 4.8L pack covers approximately 12-14 square meters at a 1mm thickness. A smaller 5kg + 1.63L pack covers about 4-4.5 square meters.Q4: What is the approximate price?A: The price is typically calculated per square meter. The approximate cost is 1650 to 2123.41 per sq. ft. (for 1mm thickness). Contact CIVILIZEMART us for the exact price of the 15kg and 5kg packs.Q5: Can it be used on drinking water tanks?A: Yes, a key advantage of Brushbond RFX is that it is non-toxic and is ideal for waterproofing potable (drinking) water tanks and reservoirs.Q6: How does it handle cracks?A: The coating is flexible and can bridge static cracks up to 1mm wide, preventing water from seeping through.Q7: What is the shelf life?A: It has a shelf life of 9 months from the date of manufacture when stored in a cool, dry place in its original, unopened packaging.Q8: Is special surface preparation needed?A: The surface must be clean, sound, and free from oil, dirt, or loose material. Light preparation like wire brushing or water jetting is usually sufficient. Large holes or cracks should be repaired first.Q9: How long does it take to dry?A: At normal temperatures (around 27°C), the first coat becomes touch-dry in 4-6 hours, after which the second coat can be applied. The mixed material has a pot life of about 30 minutes.

 91 000 74051 Complast WL Xtra - Integral Waterproofing Liquid Admixture  is a high-quality, dark brown liquid you mix directly into concrete, plaster, or mortar. It makes your structures permanently waterproof from the inside, reducing leaks and dampness. It's perfect for roofs, bathrooms, water tanks, basements, and external walls. This admixture makes concrete stronger, more durable, and easier to work with.
Key Benefits:Excellent Waterproofing: Drastically reduces water seepage in concrete.Increases Strength: Enhances the compressive strength and durability of concrete.Easy to Use: Liquid formula mixes evenly with water for consistent results.Corrosion Resistant: Protects the steel reinforcement inside the concrete.Standard Compliant: Meets Indian Standard IS:2645-2003.Approximate Market Price: 1500 - 2200 per BUCKET(20L) (Price varies based on quantity. Please contact CIVILIZEMART  for the best quote!)
Questions and Answers Q1: What is Complast WL Xtra used for?A: It is used to make concrete, plaster, and cement mortars waterproof. Common applications include terrace waterproofing, bathroom floors, water tanks, basement walls, and external plastering to prevent water leakage.Q2: How do I use this product?A: It's simple. First, mix your cement and aggregates dry. Then, add most of your mixing water. Finally, mix the required dosage of Complast WL Xtra with the remaining water and add it to the mixer. Mix for another 2 minutes, and your waterproof concrete is ready.Q3: What is the dosage per bag of cement?A: The standard dosage is 200 ml for every 50 kg bag of cement. We recommend doing a small trial mix on-site to confirm the exact dosage for your specific materials.Q4: What is the approximate price?A: The approximate market price is around 1500 to 2200 per liter. The final price depends on the order quantity (e.g., drum, bucket). Please message us for the exact, most competitive price.Q5: Can I use it with any cement?A: Yes, it is compatible with all common types of cement (OPC, PPC, PSC). However, it should not be used with High Alumina Cement.Q6: Does it affect the strength of the concrete?A: No, it maintains and can even increase the compressive strength of concrete because it allows you to use less water while maintaining workability.Q7: What are the available pack sizes?A: It is available in a wide range of sizes for your convenience: 200ml, 1L, 5L, 10L, 20L, 50L, and 200L containers.Q8: Is it safe to handle?A: Yes, it is non-toxic and non-flammable. If it splashes on your skin, wash it off with water. If it gets into your eyes, rinse thoroughly with plenty of water and seek medical attention.Q9: What is the shelf life?A: It has a shelf life of 24 months (2 years) when stored in a cool, dry place in its original, unopened container.

Nitofl or Hardtop Standard is quality controlled, factory blendedpowder which are ready to use on site. They contain special quartz-silica aggregates which have been selected forabrasion and wear resistant properties as well as shape andsize. These latter considerations, together with the use ofhigh performance workability admixtures, produces a materialwhich is easy to trowel into the surface of fresh, wet concrete.Nitofl or Hardtop Standard cure monolithically to provide adense, non-porous surface which is extremely hardwearingand abrasion resistant. Monolithic cure ensures that problemsnormally associated with thin ‘granolithic’ screeds, viz., shrinkage, cracking, etc., are completely overcome.Being non-metallic, Nitofl or Hardtop Standard provide a nonslip surface which will never rust and disintegrate

Thioflex 600 is available in gun and pouring grades. The gungrade is ideal for general application. It is packed in a readyto mix, 2.5 litre tin containing the base and curing agent in thecorrect proportions. The pouring grade for joints in horizontalsurfaces is supplied in 5 litre packs with the base and curingagent in separate tins.Thioflex 600 is particularly recommended for use in high-risebuildings and other applications where access for subsequentmaintenance will be difficult and the risk of early movementfailure must be minimised. It is also suitable for sealing jointsin brickwork, retaining walls, basements and subways.Thioflex 600 pouring grade is recommended for initial sealingof expansion joints and stress relief joints in floors and sealingother horizontal surfaces.

 91 000 74051 Complast WL Xtra - Integral Waterproofing Liquid Admixture  is a high-quality, dark brown liquid you mix directly into concrete, plaster, or mortar. It makes your structures permanently waterproof from the inside, reducing leaks and dampness. It's perfect for roofs, bathrooms, water tanks, basements, and external walls. This admixture makes concrete stronger, more durable, and easier to work with.
Key Benefits:Excellent Waterproofing: Drastically reduces water seepage in concrete.Increases Strength: Enhances the compressive strength and durability of concrete.Easy to Use: Liquid formula mixes evenly with water for consistent results.Corrosion Resistant: Protects the steel reinforcement inside the concrete.Standard Compliant: Meets Indian Standard IS:2645-2003.Approximate Market Price: 1500 - 2200 per BUCKET(20L) (Price varies based on quantity. Please contact CIVILIZEMART  for the best quote!)
Questions and Answers Q1: What is Complast WL Xtra used for?A: It is used to make concrete, plaster, and cement mortars waterproof. Common applications include terrace waterproofing, bathroom floors, water tanks, basement walls, and external plastering to prevent water leakage.Q2: How do I use this product?A: It's simple. First, mix your cement and aggregates dry. Then, add most of your mixing water. Finally, mix the required dosage of Complast WL Xtra with the remaining water and add it to the mixer. Mix for another 2 minutes, and your waterproof concrete is ready.Q3: What is the dosage per bag of cement?A: The standard dosage is 200 ml for every 50 kg bag of cement. We recommend doing a small trial mix on-site to confirm the exact dosage for your specific materials.Q4: What is the approximate price?A: The approximate market price is around 1500 to 2200 per liter. The final price depends on the order quantity (e.g., drum, bucket). Please message us for the exact, most competitive price.Q5: Can I use it with any cement?A: Yes, it is compatible with all common types of cement (OPC, PPC, PSC). However, it should not be used with High Alumina Cement.Q6: Does it affect the strength of the concrete?A: No, it maintains and can even increase the compressive strength of concrete because it allows you to use less water while maintaining workability.Q7: What are the available pack sizes?A: It is available in a wide range of sizes for your convenience: 200ml, 1L, 5L, 10L, 20L, 50L, and 200L containers.Q8: Is it safe to handle?A: Yes, it is non-toxic and non-flammable. If it splashes on your skin, wash it off with water. If it gets into your eyes, rinse thoroughly with plenty of water and seek medical attention.Q9: What is the shelf life?A: It has a shelf life of 24 months (2 years) when stored in a cool, dry place in its original, unopened container.

 91 000 74051 Brushbond RFX - Elastomeric Cementitious Waterproof Coating (Two-Component) (powder + liquid) waterproof coating that is applied by brush or trowel. It creates a flexible, seamless barrier that protects concrete and masonry structures from water, weather, chemicals, and corrosion. It is ideal for water tanks, reservoirs, basements, roofs, and structures in coastal areas. The coating is non-toxic, making it safe for potable water tanks.
Key Benefits:
Flexible & Waterproof: Bridges cracks up to 1mm and is suitable for water-retaining structures.Corrosion Protection: Excellent barrier against chloride ions, carbon dioxide, and sulphates, protecting steel reinforcement.Breathable: Allows water vapour to escape, preventing blistering.UV & Weather Resistant: Durable in all climates, including coastal environments.Non-Toxic: Safe for use in drinking water tanks.
Easy Application: Can be applied by brush, roller, or trowel.
Approximate Market Price: ₹1650 - ₹2123.41 per PACK (for 1mm thickness). Please contact CIVILIZEMART for package pricing!
Questions and Answers:Q1: What is Brushbond RFX used for?A: It is used for waterproofing and protecting concrete structures like water tanks, reservoirs, basements, drainage culverts, and roofs. It is especially good for coastal buildings as it protects against salt and weather damage.Q2: How is it applied?A: It is a two-part system. You mix the powder with the liquid polymer (Nitobond BBX) and water. The mixed paste is then applied like paint using a stiff brush or roller in two coats to achieve a 1mm thickness.Q3: What is the coverage area?A: A standard 15kg + 4.8L pack covers approximately 12-14 square meters at a 1mm thickness. A smaller 5kg + 1.63L pack covers about 4-4.5 square meters.Q4: What is the approximate price?A: The price is typically calculated per square meter. The approximate cost is 1650 to 2123.41 per sq. ft. (for 1mm thickness). Contact CIVILIZEMART us for the exact price of the 15kg and 5kg packs.Q5: Can it be used on drinking water tanks?A: Yes, a key advantage of Brushbond RFX is that it is non-toxic and is ideal for waterproofing potable (drinking) water tanks and reservoirs.Q6: How does it handle cracks?A: The coating is flexible and can bridge static cracks up to 1mm wide, preventing water from seeping through.Q7: What is the shelf life?A: It has a shelf life of 9 months from the date of manufacture when stored in a cool, dry place in its original, unopened packaging.Q8: Is special surface preparation needed?A: The surface must be clean, sound, and free from oil, dirt, or loose material. Light preparation like wire brushing or water jetting is usually sufficient. Large holes or cracks should be repaired first.Q9: How long does it take to dry?A: At normal temperatures (around 27°C), the first coat becomes touch-dry in 4-6 hours, after which the second coat can be applied. The mixed material has a pot life of about 30 minutes.

 91 000 74051 Complast WL Xtra - Integral Waterproofing Liquid Admixture  is a high-quality, dark brown liquid you mix directly into concrete, plaster, or mortar. It makes your structures permanently waterproof from the inside, reducing leaks and dampness. It's perfect for roofs, bathrooms, water tanks, basements, and external walls. This admixture makes concrete stronger, more durable, and easier to work with.
Key Benefits:Excellent Waterproofing: Drastically reduces water seepage in concrete.Increases Strength: Enhances the compressive strength and durability of concrete.Easy to Use: Liquid formula mixes evenly with water for consistent results.Corrosion Resistant: Protects the steel reinforcement inside the concrete.Standard Compliant: Meets Indian Standard IS:2645-2003.Approximate Market Price: 1500 - 2200 per BUCKET(20L) (Price varies based on quantity. Please contact CIVILIZEMART  for the best quote!)
Questions and Answers Q1: What is Complast WL Xtra used for?A: It is used to make concrete, plaster, and cement mortars waterproof. Common applications include terrace waterproofing, bathroom floors, water tanks, basement walls, and external plastering to prevent water leakage.Q2: How do I use this product?A: It's simple. First, mix your cement and aggregates dry. Then, add most of your mixing water. Finally, mix the required dosage of Complast WL Xtra with the remaining water and add it to the mixer. Mix for another 2 minutes, and your waterproof concrete is ready.Q3: What is the dosage per bag of cement?A: The standard dosage is 200 ml for every 50 kg bag of cement. We recommend doing a small trial mix on-site to confirm the exact dosage for your specific materials.Q4: What is the approximate price?A: The approximate market price is around 1500 to 2200 per liter. The final price depends on the order quantity (e.g., drum, bucket). Please message us for the exact, most competitive price.Q5: Can I use it with any cement?A: Yes, it is compatible with all common types of cement (OPC, PPC, PSC). However, it should not be used with High Alumina Cement.Q6: Does it affect the strength of the concrete?A: No, it maintains and can even increase the compressive strength of concrete because it allows you to use less water while maintaining workability.Q7: What are the available pack sizes?A: It is available in a wide range of sizes for your convenience: 200ml, 1L, 5L, 10L, 20L, 50L, and 200L containers.Q8: Is it safe to handle?A: Yes, it is non-toxic and non-flammable. If it splashes on your skin, wash it off with water. If it gets into your eyes, rinse thoroughly with plenty of water and seek medical attention.Q9: What is the shelf life?A: It has a shelf life of 24 months (2 years) when stored in a cool, dry place in its original, unopened container.

 91 000 74051 Complast WL Xtra - Integral Waterproofing Liquid Admixture  is a high-quality, dark brown liquid you mix directly into concrete, plaster, or mortar. It makes your structures permanently waterproof from the inside, reducing leaks and dampness. It's perfect for roofs, bathrooms, water tanks, basements, and external walls. This admixture makes concrete stronger, more durable, and easier to work with.
Key Benefits:Excellent Waterproofing: Drastically reduces water seepage in concrete.Increases Strength: Enhances the compressive strength and durability of concrete.Easy to Use: Liquid formula mixes evenly with water for consistent results.Corrosion Resistant: Protects the steel reinforcement inside the concrete.Standard Compliant: Meets Indian Standard IS:2645-2003.Approximate Market Price: 1500 - 2200 per BUCKET(20L) (Price varies based on quantity. Please contact CIVILIZEMART  for the best quote!)
Questions and Answers Q1: What is Complast WL Xtra used for?A: It is used to make concrete, plaster, and cement mortars waterproof. Common applications include terrace waterproofing, bathroom floors, water tanks, basement walls, and external plastering to prevent water leakage.Q2: How do I use this product?A: It's simple. First, mix your cement and aggregates dry. Then, add most of your mixing water. Finally, mix the required dosage of Complast WL Xtra with the remaining water and add it to the mixer. Mix for another 2 minutes, and your waterproof concrete is ready.Q3: What is the dosage per bag of cement?A: The standard dosage is 200 ml for every 50 kg bag of cement. We recommend doing a small trial mix on-site to confirm the exact dosage for your specific materials.Q4: What is the approximate price?A: The approximate market price is around 1500 to 2200 per liter. The final price depends on the order quantity (e.g., drum, bucket). Please message us for the exact, most competitive price.Q5: Can I use it with any cement?A: Yes, it is compatible with all common types of cement (OPC, PPC, PSC). However, it should not be used with High Alumina Cement.Q6: Does it affect the strength of the concrete?A: No, it maintains and can even increase the compressive strength of concrete because it allows you to use less water while maintaining workability.Q7: What are the available pack sizes?A: It is available in a wide range of sizes for your convenience: 200ml, 1L, 5L, 10L, 20L, 50L, and 200L containers.Q8: Is it safe to handle?A: Yes, it is non-toxic and non-flammable. If it splashes on your skin, wash it off with water. If it gets into your eyes, rinse thoroughly with plenty of water and seek medical attention.Q9: What is the shelf life?A: It has a shelf life of 24 months (2 years) when stored in a cool, dry place in its original, unopened container.

 91 000 74051 Fosroc Renderoc Plug is a rapid-setting, cement-based plugging mortar specially designed for stopping water leakages instantly in concrete and masonry structures. It forms a strong, durable, and watertight seal within minutes.
✔ Fast setting – stops running water in 1–2 minutes✔ Non-shrink, chloride-free, safe for concrete✔ High adhesion to damp/wet surfaces✔ Easy to apply – just mix with water and press into the leak✔ Durable waterproof sealing
Applications:
Instant water leak plugging in basements, lift pits, tunnels
Sealing leaks in water tanks, overhead tanks, and reservoirs
Emergency leakage repair in dams, canals, and culverts
Waterproofing for concrete & masonry structures
Packaging: 1 kg, 5 kg, and 15 kg packs

Q1. What is Fosroc Renderoc Plug used for?�� It is used for instant stopping of water leakages in concrete and masonry structures.
Q2. How fast does it set?�� It sets in about 1–2 minutes, depending on water temperature.
Q3. Can it be applied on wet surfaces?�� Yes, it bonds well to wet and damp surfaces.
Q4. Is it suitable for drinking water tanks?�� Yes, it is chloride-free and non-toxic, making it safe for potable water structures.
Q5. What is the method of application?�� Mix the powder with water into a stiff paste and press into the leaking point by hand until set.
Q6. What pack sizes are available?�� 1 kg, 5 kg, and 15 kg packs.
Q7. What is the shelf life?�� 12 months in sealed bags, stored in a dry place.

Q8. What is the price of Fosroc Renderoc Plug?�� Market price usually ranges between ₹350–₹450 per 1 kg pack, depending on location and supplier. Larger packs (5 kg / 15 kg) are available at discounted rates. Contact Civilize Mart for the latest wholesale and retail price.

 91 000 74051 Brushbond RFX - Elastomeric Cementitious Waterproof Coating (Two-Component) (powder + liquid) waterproof coating that is applied by brush or trowel. It creates a flexible, seamless barrier that protects concrete and masonry structures from water, weather, chemicals, and corrosion. It is ideal for water tanks, reservoirs, basements, roofs, and structures in coastal areas. The coating is non-toxic, making it safe for potable water tanks.
Key Benefits:
Flexible & Waterproof: Bridges cracks up to 1mm and is suitable for water-retaining structures.Corrosion Protection: Excellent barrier against chloride ions, carbon dioxide, and sulphates, protecting steel reinforcement.Breathable: Allows water vapour to escape, preventing blistering.UV & Weather Resistant: Durable in all climates, including coastal environments.Non-Toxic: Safe for use in drinking water tanks.
Easy Application: Can be applied by brush, roller, or trowel.
Approximate Market Price: ₹1650 - ₹2123.41 per PACK (for 1mm thickness). Please contact CIVILIZEMART for package pricing!
Questions and Answers:Q1: What is Brushbond RFX used for?A: It is used for waterproofing and protecting concrete structures like water tanks, reservoirs, basements, drainage culverts, and roofs. It is especially good for coastal buildings as it protects against salt and weather damage.Q2: How is it applied?A: It is a two-part system. You mix the powder with the liquid polymer (Nitobond BBX) and water. The mixed paste is then applied like paint using a stiff brush or roller in two coats to achieve a 1mm thickness.Q3: What is the coverage area?A: A standard 15kg + 4.8L pack covers approximately 12-14 square meters at a 1mm thickness. A smaller 5kg + 1.63L pack covers about 4-4.5 square meters.Q4: What is the approximate price?A: The price is typically calculated per square meter. The approximate cost is 1650 to 2123.41 per sq. ft. (for 1mm thickness). Contact CIVILIZEMART us for the exact price of the 15kg and 5kg packs.Q5: Can it be used on drinking water tanks?A: Yes, a key advantage of Brushbond RFX is that it is non-toxic and is ideal for waterproofing potable (drinking) water tanks and reservoirs.Q6: How does it handle cracks?A: The coating is flexible and can bridge static cracks up to 1mm wide, preventing water from seeping through.Q7: What is the shelf life?A: It has a shelf life of 9 months from the date of manufacture when stored in a cool, dry place in its original, unopened packaging.Q8: Is special surface preparation needed?A: The surface must be clean, sound, and free from oil, dirt, or loose material. Light preparation like wire brushing or water jetting is usually sufficient. Large holes or cracks should be repaired first.Q9: How long does it take to dry?A: At normal temperatures (around 27°C), the first coat becomes touch-dry in 4-6 hours, after which the second coat can be applied. The mixed material has a pot life of about 30 minutes.

 91 000 74051 Brushbond RFX - Elastomeric Cementitious Waterproof Coating (Two-Component) (powder + liquid) waterproof coating that is applied by brush or trowel. It creates a flexible, seamless barrier that protects concrete and masonry structures from water, weather, chemicals, and corrosion. It is ideal for water tanks, reservoirs, basements, roofs, and structures in coastal areas. The coating is non-toxic, making it safe for potable water tanks.
Key Benefits:
Flexible & Waterproof: Bridges cracks up to 1mm and is suitable for water-retaining structures.Corrosion Protection: Excellent barrier against chloride ions, carbon dioxide, and sulphates, protecting steel reinforcement.Breathable: Allows water vapour to escape, preventing blistering.UV & Weather Resistant: Durable in all climates, including coastal environments.Non-Toxic: Safe for use in drinking water tanks.
Easy Application: Can be applied by brush, roller, or trowel.
Approximate Market Price: ₹1650 - ₹2123.41 per PACK (for 1mm thickness). Please contact CIVILIZEMART for package pricing!
Questions and Answers:Q1: What is Brushbond RFX used for?A: It is used for waterproofing and protecting concrete structures like water tanks, reservoirs, basements, drainage culverts, and roofs. It is especially good for coastal buildings as it protects against salt and weather damage.Q2: How is it applied?A: It is a two-part system. You mix the powder with the liquid polymer (Nitobond BBX) and water. The mixed paste is then applied like paint using a stiff brush or roller in two coats to achieve a 1mm thickness.Q3: What is the coverage area?A: A standard 15kg + 4.8L pack covers approximately 12-14 square meters at a 1mm thickness. A smaller 5kg + 1.63L pack covers about 4-4.5 square meters.Q4: What is the approximate price?A: The price is typically calculated per square meter. The approximate cost is 1650 to 2123.41 per sq. ft. (for 1mm thickness). Contact CIVILIZEMART us for the exact price of the 15kg and 5kg packs.Q5: Can it be used on drinking water tanks?A: Yes, a key advantage of Brushbond RFX is that it is non-toxic and is ideal for waterproofing potable (drinking) water tanks and reservoirs.Q6: How does it handle cracks?A: The coating is flexible and can bridge static cracks up to 1mm wide, preventing water from seeping through.Q7: What is the shelf life?A: It has a shelf life of 9 months from the date of manufacture when stored in a cool, dry place in its original, unopened packaging.Q8: Is special surface preparation needed?A: The surface must be clean, sound, and free from oil, dirt, or loose material. Light preparation like wire brushing or water jetting is usually sufficient. Large holes or cracks should be repaired first.Q9: How long does it take to dry?A: At normal temperatures (around 27°C), the first coat becomes touch-dry in 4-6 hours, after which the second coat can be applied. The mixed material has a pot life of about 30 minutes.

Nitobond SBR is a modified styrene butadiene rubber emulsion which is supplied as a ready to use white liquid. It is designed to improve the qualities of site-batched cementitious mortars and slurries. Being resistant to hydrolysis, it is ideal for internal and external applications in conjunction with cement.

Nitobond SBR(Latex) is modifi ed styrene butadiene emulsionspecially designed for use as a bonding aid and gauging liquidfor cementitious systems. It is resistant to hydrolysis and cantherefore be used for external applications too.

Fosroc Conplast SP430 Dis is a high-performance super plasticizer admixture specially formulated to enhance the workability and durability of concrete mixes. This advanced additive disperses cement particles effectively, resulting in improved flow characteristics without compromising on strength. Its unique formulation allows for significant water reduction, leading to increased concrete strength, reduced permeability, and enhanced durability. Suitable for a wide range of applications including precast concrete, ready-mix concrete, and shotcrete, Fosroc Conplast SP430 Dis ensures superior performance and consistent results.