Civilize Mart

•  91 000 74051 NCL LFT Adhesive TE 203 is a cement-based, polymer-modified thin-bed adhesive from NCL, designed for fixing tiles/stones. 

• It’s supplied as a factory-premixed dry powder; on-site you just add water and mix (i.e. “single-pack, just-add-water” system) — no need for custom cement-sand mixes. 

• It conforms to standards IS 15477:2019 — Type 4 and EN 12004: C2TS2. 

• It is formulated especially for larger-format tiles and stones, including vitrified / porcelain tiles, slim tiles, marble, granite, engineered stones — suitable where high bond-strength and full bed coverage is needed.

�� Key Properties & Benefits

• Strong & durable bond — high tensile adhesion strength helps prevent debonding, hollow-sound issues or loose tiles over time. 

• Water-resistant & suitable for wet / monsoon-prone conditions — TE 203 is advertised as water-resistant and impact-resistant, making it reliable for areas exposed to moisture/rain, e.g. bathrooms, balconies, external walls. 

• Flexibility / Impact resistance — the polymer-modified formulation offers good flexibility, which helps accommodate minor substrate/tile movements without cracking or debonding. 

• Versatile: Interior & Exterior, Floors & Walls & Cladding — usable on internal floors/walls, external walls, even external cladding (up to around 10 ft from ground level, per manufacturer) when done properly. 

• Wide substrate compatibility — can be applied on cement plaster, concrete, screeds; also works on drywall boards, plywood, certain panels (for cladding), subject to primer/ substrate prep if needed.

• Full-bed application — thin-bed adhesive but formulated to ensure full contact under tile, avoiding hollow voids common with poor mortar-mix tile fixing. 

�� Technical / Application Details

• Tile / tile-type suitability: vitrified tiles, porcelain, slim tiles, large-format tiles/stones, marble / granite / engineered stones — especially materials with porosity < ~3%. Adhesive bed thickness: ~ 3 mm up to ~ 12 mm depending on application.

• Coverage: Approx. 0.278–0.306 m² per kg (with 6 × 6 mm notch trowel) — actual coverage depends on notch size, tile type etc. 

• Packaging: Commonly available in 20 kg or 50 kg bags.

�� Where & When You Should Use TE 203

Use NCL LFT Adhesive-TE 203 when:

• Installing large-format tiles or heavy stone tiles / slabs (porcelain, marble, granite, engineered stone) on floors or walls.

• Working in wet or high-moisture zones, or in climates with heavy rainfall / monsoon — e.g. bathrooms, balconies, external walls, terraces (provided substrate is correct

• Expecting heavy traffic, impact, or heavy load conditions (entrances, corridors, commercial floors, etc.) where a strong, long-lasting bond is necessary.

• Building projects where you want reliable, factory-consistent adhesive performance rather than variable traditional cement-sand mixes.

⚠️ What to Check / Limitations / Good Practices

• Substrate must be properly prepared: level, clean, stable, free from dust/oil/loose particles before applying adhesive — as with any tile adhesive. Poor substrate prep reduces bond strength.

•  91 000 74051 NCL LFT Flex Adhesive TE-204 is a cement-based, polymer-modified thin-bed adhesive. 

• It is supplied as a factory-premixed dry powder — on site you add water to mix (single-pack, ready-to-use) instead of doing a cement-sand mortar mix. 

• It’s intended for fixing extra-large format tiles and stones — including vitrified/porcelain tiles, slim tiles, natural stones (marble, granite), engineered stones — on properly prepared floors or walls. 

• High bonding strength — ensures full-bed contact under tiles/stone, avoiding hollow-voids or poor adhesion often seen with traditional mortar.Very good flexibility & impact resistance — polymer modification gives it some flexibility, which helps in areas where substrate or tile might experience slight movement, thermal variation or impact.

• Water resistant — suitable for wet-areas installation (bathrooms, balconies, exterior, etc.) when substrate & tiles are suitable.

• Suitable for interior & exterior applications, including wall and floor — and reportedly usable for external cladding up to about 15 ft from ground level (as per manufacturer note) when correctly applied. 

• Single-pack (powder + water) and factory premixed: makes on-site mixing simpler, more consistent quality, less wastage vs traditional mortar.

• Works for tiles / stones with low porosity (porosity < ~3 %) — good for vitrified/porcelain, slim tiles, marble/ granite etc. 

• Large-format vitrified/porcelain tiles, slim tiles, natural stones (marble, granite, engineered stone) to install on floors or walls.

• Both interior and exterior tiling jobs — e.g. balconies, terraces, external walls (within recommended height limits).

• Areas requiring water resistance and durability — bathrooms, kitchens, wet balconies, external exposures (with proper waterproofing measures).

• Substrate preparation is crucial: surface must be properly cleaned, levelled, stable, free of loose particles, dust, oil, paint etc. Poor substrate prep will reduce adhesion strength — as with any tile adhesive.

• Tile porosity: best suited for low-porosity tiles/stones (vitrified/porcelain/slim/stone). Highly porous tiles or surfaces with high moisture absorption may not bond optimally.

• Full-bed application recommended — ensure adhesive bed and coverage is uniform under tile to prevent hollow spots.

• For exterior tiling or wet zones — additional waterproofing / drainage / sealing measures should be considered (adhesive helps but is not a substitute for full waterproofing).

• Check load / stress conditions: For extremely heavy slabs or very large stones — ensure adhesive + substrate + backing are all compatible.

 

• 91 000 74051 NCL LFT O Flex Adhesive TE 205 is a cement-based, polymer-modified thin-bed tile/stone adhesive. 

• It comes as a factory-prepared dry powder, so on-site you just mix with water — no need for manual cement-sand mortar mixing.  

• It is designed specifically for extra-large format tiles and stones, and for use on levelled walls & floors.  

According to the manufacturer’s product information, TE 205 offers: High bonding strength — ensures full-bed adhesive coverage under tiles/stones instead of risking hollow spots or weak bonding associated with traditional mortar methods. 

• Flexibility & impact resistance — polymer modification gives the adhesive some flexibility, which helps accommodate minor structural movements, thermal expansion/contraction, or impact, reducing tile stress. 

• Suitable for interior and exterior applications, including external cladding up to 25 ft from ground level (as per manufacturer’s spec) when properly applied. 

• Works with low-porosity tile/stone types — such as vitrified tiles, porcelain tiles, slim tiles, marble, granite, engineered stone, mosaic, and tile-on-tile applications (provided porosity < ~3%).

• Usable on a variety of substrates: cement plaster, concrete, cement screed, drywall board (gypsum), plywood, calcium silicate board, medium-density fibre board (MDF), and certain panels — which makes it versatile for both floor and wall tiling or cladding. 

• Single-pack, water-mixable, self-curing — simplifies onsite work compared to traditional mortar mixes.

• Water-resistant — suitable for wet areas (provided correct tiles & substrate), making it usable in bathrooms, kitchens, balconies, terraces, etc. 

• Laying large-format tiles or heavy stone/porcelain slabs (vitrified, porcelain, marble, granite, engineered stone) on floors or walls.

• Doing internal or external tile/stone installation, including cladding (since it supports external cladding up to 25 ft).

• Working in wet or moisture-prone areas — bathrooms, kitchens, balconies, terraces — where water resistance + strong adhesion is needed.

• Wanting strong, full-bed bonding rather than spot-fix or weak mortar bonding — especially important for heavy tiles/stones to avoid hollow-sound under tiles, cracking, or debonding.

• Seeking ease of use: with ready-mix powder + water (single pack) — faster work, less labour compared to traditional mortar mixing.

• Use only for tiles/stones with low porosity (as recommended) — high-porosity or very absorbent tiles may not bond as well.

•  

 

•  91 000 74051 NCL Megamix-Set is a polymer additive (milky-liquid) used for tile/stone fixing — not a food-processor or kitchen appliance. 

• It is designed to be mixed with water and then combined with cement (grey or white) to form a cement slurry — used for installing tiles or stones on floors over a levelling bed. 

✅ Key Features & Benefits

• Improved adhesion & bond strength — helps cement slurry adhere tiles/stones firmly so they stay in place over time. 

• High water retention & spreadability — ensures the slurry stays workable longer and spreads evenly under tiles, reducing risk of “hollow spots” or poor bonding.

• Self-curing property — helps curing process and improves final durability of tile installation. 

• Good adjustability time — after placing tile, you have about 8 minutes to adjust position before the set begins fixing.

• Compatible with grey & white cement — usable with both common cement types. 

• Economical & practical — meant as a cost-effective upgrade to traditional cement slurry for tile/stone work. 

�� Technical / Usage Details

• Appearance: milky liquid.

• Density: ~ 1.02 g/ml (±0.02) 

• Open time (workable after mixing): ~ 15 minutes 

• Adjustability (after tile placement): ~ 8 minutes 

• For floor tile/stone installation over cement-based levelling beds (interior & exterior), not recommended for wall tile fixing. 

• Packaging available: 300 ml and 900 ml bottles

�� When & Where to Use It

Use NCL Megamix-Set when:

• you are laying tile or stone flooring over a freshly prepared levelling bed (cement mortar/concrete),

• you want stronger adhesion and better durability than raw cement slurry alone,

• you want to avoid hollow-sound tiles (which indicate poor bonding),

• you need a cost-effective yet reliable solution for interior or exterior floors (residential or commercial).

• 91 000 74051 NCL OMNISTIK TE-106 is a cement-based, polymer-modified, single-component thin-bed tile adhesive from NCL Buildtek.

• It comes as a dry-powder blend — you just add the recommended amount of water at site, mix, and apply. No need for traditional cement-sand mixes.

• It’s designed for both floor and wall tiling, and supports a wider variety of tiles including ceramic, vitrified, and some stone tiles.

✔ Standard-size ceramic or vitrified tiles on walls & floors
✔ Interior living spaces, balconies, kitchens, bathrooms
✔ Residential and light commercial applications
✔ New constructions and renovation jobs
✔ Situations needing fast and consistent bonding without manual mortar mixing

Especially good because:

• It’s easy to mix / ready to use — saves labor and time on site

• Gives consistent strength, reduced chances of hollow spots, and good adhesion

• Works on multiple substrates like concrete, plaster, screed, etc.

• Ensure the substrate is clean, level, stable, and free of dust/oil/loose particles.

• Avoid use in continuously wet environments or heavy water exposure areas (like outdoor pool edges) unless paired with proper waterproofing.

• For very large or very heavy stone tiles (marble/granite/slabs) — consider a stronger/high-flex adhesive (e.g., NCL Cerostik TI-103, Tilostik TE-105, or NCL Platinum-grade adhesives).

• Follow proper trowel notch size and full-bed application to eliminate voids under tiles.

91 000 74051 NCL SCREED 25 is grey cement-based with high polymer modified single pack screed. This high quality factory premixed dry powder incorporates special chemical additives and inorganic fillers. It is specifically designed for interior and exterior applications, effectively levelling floors on cement concrete and mortar beds. Features: Assured factory quality Eliminates site batch mix variations Single pack system, need to add only water as per recommendation ☑ High strength Non-shrinkage Excellent impact resistance Saves considerable time & labor Screed thickness Low VOС Application: For internal & external application on cement mortar bed and concrete slab & for levelling the floor Covering: NA Substrate: Any PCC, RCC or sound flooring Colour: Grey Coverage: Upto 6 sq.ft./Kg Thickness: Upto 35 mm Pack size: 25k

•  91 000 74051 NCL Tilostik is a cement-based, polymer-modified thin-bed tile adhesive from NCL Buildtek. 

• It’s distributed as a dry-powder adhesive. On-site you simply add water (single-pack system) and mix — no need for custom cement-sand mixes. 

• It is meant for fixing tiles (ceramic, vitrified, certain stones) and is suitable for both wall and floor applications on leveled, prepared substrates (concrete, screed, cement plaster, etc.). 

• Color / appearance: Grey (or white version depending on supply) dry powder.

• Mixing with water — roughly 25–30% water by weight is recommended for proper consistency. 

• Pot life / working time: ~ 180 minutes after mixing (gives you sufficient time for application) 

• Bed thickness (adhesive layer): minimum ~ 3 mm, can vary depending on tile size and job requirements. 

• Open time (time you have to adjust tiles after placing adhesive): > 20 minutes (at ~25 °C) — gives flexibility during installation. 

• Coverage (approx): For a 3 mm bed thickness — stated as > 3 sqft per kg (so a 20 kg bag covers significantly, though actual depends on trowel size, tile size, substrate condition). Time to traffic (after which you can walk / grout / use floor): ~ 24 hours after laying. 

• Because it’s polymer-modified and premixed, it gives a strong, reliable bond — better and more consistent than traditional cement-sand mortar mixing onsite. 

• It helps avoid “hollowness” (voids or air-gaps under tiles) even under stone or compact tiles, giving a solid, stable finish for floors.

• Versatile — usable for interior and exterior applications, on walls and floors, on various cementitious substrates (plaster, screed, concrete) — good for residential and commercial / renovation jobs. 

• Because of consistent factory-prepared mix, it reduces labor, wastage, and variation compared to manual mortar mixes — convenient for faster tile installation. 

• The substrate (floor/wall surface) must be clean, level, stable, free of dust/oil/loose particles for good adhesion (as with any tile adhesive).

• While advertised for “tiles and stones”, performance will depend on tile/stone type — make sure tile porosity / size / weight is within what Tilostik is suitable for (moderate to normal-size tiles, not extremely heavy slabs).

• Use proper trowel notch size (as recommended by installer) and apply adhesive evenly for full bed coverage to avoid weak bonding or hollow spots.

 91 000 74051 NCL ULTIMATE FLEX ADHESIVE is a cement based thin bed adhesive, available in grey or white, that has been extensively polymer modified for the secure installation of extra large tiles and stones on levelled walls & floors. This high quality, factory prepared dry powder includes specialized chemical additives & inorganic fillers. It delivers exceptional bonding strength, ensuring full coverage of the tile surface. This results in a robust, longlasting installation, as opposed to the weaker, less reliable installations associated with traditional mortar. It has good flexible property, impact resistance and water resistance with extendable open time. Features: Self curing Low VОС . Water resistant Suitable for interior & exterior applications Good impact resistant ◆ Excellent tensile ◆ 2 pack system, need to add 5.5-• 6 ltr. Admix- TAD AE 406 for 20kg dry filler pack- 1 as per recommendation •Multi purpose application adhesion strength Good open time Excellent flexible property For external cladding upto 30ft. from ground level Application: For internal and external application on wall & floor and external cladding Covering: Suitable for tiles with porosity less than 3% such as vitrified tiles, porcelain tiles, slim tiles, tile on tile, mosaic tiles, marble, granite & engineered stones Substrate: Cement plastered, cement concrete, cement screed, wet areas, drywall board (gypsum), plywood, calcium silicate, medium density fibreboards, bison panels for external cladding tile on tile (for dry wall applications primer has to be applied) Colour: Grey & White Coverage: Upto 3.5 sq.ft./Kg Thickness: 3mm - 12mm Pack size: Dry fil 20 kg & AE 409-5litres
coverage:- upto 3.5 sq.ft /kg when applied with 6*6mm notch trowel

 91 000 74051 NCL Vitristik – TE 104 - Premium Adhesive for Vitrified Tiles & Stone is a high-performance, polymer-modified cement-based adhesive specially formulated for installing large-format vitrified tiles (up to 600x600 mm) and stone. It provides exceptional bond strength for both interior and exterior (covered) walls and floors, including wet areas like bathrooms. Available in grey and white, it ensures durable, long-lasting installations.
Key Benefits:
Strong Bond for Vitrified Tiles: Expertly formulated for tiles with low porosity (<3%).Versatile Use: Suitable for interior & exterior (covered) walls, floors, and wet areas.High Performance: Conforms to IS 15477 Type 2 and European EN 12004 C1TS1 standards.Easy Application: Good open time and just-add-water formula save time and labour.Full Coverage: Ensures a robust installation without hollow spots.Approximate Market Price: 360 - 490 per 20 kg bag (Contact CIVILIZEMART for 50kg project pricing!)
Questions and Answers:Q1: What is the main use of NCL Vitristik TE 104?A: It is specifically designed for installing large-format vitrified tiles (up to 600x600mm) and natural stone on walls and floors, both indoors and in covered outdoor areas.Q2: Can it be used in bathrooms and wet areas?A: Yes. As a Type 2 adhesive, it is water-resistant and perfectly suitable for wet areas like bathrooms, kitchen splash backs, and balconies (under covered areas).Q3: What is the coverage area per bag?A: Coverage is approximately 0.255 - 0.278 sq. meters per kg. A 20kg bag will cover about 5.1 to 5.5 square meters when applied with a 6mm x 6mm notch trowel.Q4: What is the approximate price?A: The approximate price for a 20kg bag is 360 TO 490. Please message us for the exact best price and quotes for 50kg bags.Q5: What is the advantage of using this over a standard adhesive for vitrified tiles?A: Vitrified tiles have very low porosity, requiring a high-strength, polymer-modified adhesive for a secure bond. TE 104 is engineered for this purpose, preventing tile slippage or debonding, which is a risk with standard mortars.Q6: Is it available in white color?A: Yes, it is available in both Grey and White colors. The white variant is ideal for light-colored tiles and translucent stones where grey adhesive might show through.Q7: What surfaces can it be applied on?A: It can be applied on cement plaster, cement concrete, cement screed, and over existing tiles in wet areas (with proper surface preparation).Q8: What does the EN C1TS1 classification mean?A: This European standard certification means it is a Cementitious (C1) adhesive with improved Slip Resistance (T) and Standard Open Time (S1), confirming its high quality and reliability.Q9: Who manufactures this product?A: It is manufactured by NCL Buildtek Ltd., a company known for its quality and innovative construction chemical solutions.Q10: How do I order?A: You can order directly through us on CIVILIZEMART. Contact us for pricing, availability of grey/white variants.

91 000 74051 NCL Cerostik FL – TI 100 - Polymer Modified Tile Adhesive for Interior Floors is a ready-to-use, grey cement-based adhesive for fixing small ceramic and clay tiles (up to 300mm x 300mm) on interior floors. Its polymer-modified formula ensures a strong, reliable bond without the need to soak tiles beforehand. It's a fast, efficient, and user-friendly solution for interior tiling projects. 
Key Benefits:
Strong Bond: Provides high bonding strength for durable tile installation.Time-Saving: No need to soak tiles before fixing, speeding up the process.Easy to Use: Factory-premixed powder ensures consistent quality and easy application.Standard Compliant: Conforms to IS 15477:2019 – Type 1 standards.Versatile: Primarily for interior floors but can also be used on interior walls*.Approximate Market Price: 250 - 390 per 20 kg bag (Contact CIVILIZEMART for 50kg project pricing!)Questions and Answers:Q1: What types of tiles is this adhesive suitable for?A: It is designed for fixing small-format clay and ceramic tiles (up to 300mm x 300mm) with a porosity greater than 3%. It is ideal for common ceramic tiles used in interior spaces.Q2: Can it be used in bathrooms or wet areas?A: This product is classified as Type 1, which is generally intended for interior dry areas. For bathrooms, balconies, or other wet areas, a water-resistant (Type 2) adhesive is recommended.Q3: What is the coverage area per bag?A: The coverage is approximately 0.278 square meters per kg. This means a 20kg bag will cover about 5.5 square meters when applied with a 6mm x 6mm notch trowel.Q4: What is the approximate price?A: The approximate price for a 20kg bag is 250 TO 390. Please contact us CIVILIZEMART for the most current pricing and for quotes on 50kg bags for larger projects.Q5: Do I need to soak the tiles before fixing?A: No. A key advantage of this adhesive is that it eliminates the need to soak the tiles before installation, saving time and effort.Q6: What surfaces can it be applied on?A: It can be applied on cement plaster, cement concrete, and cement screed. The surface must be level, clean, and sound.Q7: What is the recommended application thickness?A: It is a thin-bed adhesive designed for a thickness between 3mm and 10mm.

•  91 000 74051 NCL CEROSTIK TI-103 is a cement-based, polymer-modified thin-bed tile adhesive. It’s a pre-mixed dry powder adhesive: you just add water on site, mix and apply — no need for custom cement-sand mixes. 

• It conforms to standard: IS 15477:2019 (Type 1) and also meets EN 12004 classification C1T. 

�� Technical Specs & Suitable Use ✅ What It’s Good For

• Installing ceramic/clay tiles in interior rooms — walls or floors. Good for bathrooms, kitchens, living areas (provided tiles suit).

• Jobs where you want a ready-mix adhesive (less site-work compared to cement-sand mortar), to save labour and get consistent quality.

• Projects where smaller tiles or standard-format tiles are used — since TI-103 is meant for small/medium tiles rather than heavy or large-format stone/tiles.

• Surfaces like cement plaster, concrete, screed, existing mortar beds — typical for Indian residential/commercial internal tiling.

⚠️ What to Consider / Where It May Not Be Ideal

• Not ideal for large-format tiles, heavy stone (granite/marble), or heavy-duty outdoor tiling — the product is meant for small/medium ceramic/clay tiles.

• For exterior or damp/wet exposed areas (like open terraces, pool-sides, heavy moisture zones) — unless conditions are controlled and tiles are small — better to use heavier-duty adhesive.

• As with any adhesive: substrate must be clean, level, dry, and free from dust/oil/loose plaster/paint before application. This ensures adhesion strength and durability.

•  91 000 74051 It is a cement-based, polymer-modified tile grout designed to fill the joints between tiles after they are laid. 

• Meant to give a finished, smooth, water-resistant joint that strengthens the tile installation and improves durability. 

• Suitable for various tile types: ceramic, vitrified tiles, natural stone, mosaic tiles. 

• Works on both walls and floors, and can be used for interior and exterior applications. 

• Suitable for tiling jobs using floor tiles, wall tiles, natural stone, mosaic, vitrified tiles. 

• Tile joints of widths from about 1 mm to 8 mm — so both narrow and moderate-width grout joints. 

• It comes in small packs: e.g. 1 kg or 5 kg bags.

• Used by professionals and DIY for tiling & grouting jobs where a clean, water-resistant finish is needed.