SIKA

Product Details:

Sikadur®-42 HES IN 3-part high performance pourable epoxy grout DESCRIPTION Sikadur®-42 HES IN is a 3-part, high-performance, high precision, pourable, and solvent-free moisture-tolerant epoxy grout which develops high early strength. It is suitable for many static or dynamic precision grouting applications. It has a layer thickness of 25 mm to 75 mm and an application temperature range of +10 °C to +35 °C. USES Sikadur®-42 HES IN may only be used by experienced professionals. The Product is used for high-strength grouting and fixing of the following elements: ▪ Starter bars ▪ Anchors ▪ Tie rods ▪ Fasteners ▪ Crash barrier posts ▪ Fence and railing posts The Product is used for precision under-grouting and bedding of the following elements: Machine bases, base plates for light and heavy machinery including heavy-impact and vibratory machinery, reciprocating engines, compressors, pumps and presses ▪ ▪ Bridge bearings ▪ Mechanical joints in road, bridges, deck, etc. The Product is used for sleeper-less, direct rail fixing: ▪ Crane tracks ▪ Light rail and permanent way in tunnels ▪ Light rail and permanent way over bridges The Product is used for repairing the following concrete elements: ▪ Spalled concrete structures ▪ Industrial floor slabs ▪ Hole and void filling ▪ Runways ▪ Hardstandings ▪ Car park decks The Product is used for interior and exterior applications. CHARACTERISTICS / ADVANTAGES ▪ High early strength ▪ Ready-to-mix, pre-batched units ▪ Good flowability ▪ Tolerant to substrates with high moisture content ▪ Good mechanical resistance ▪ Very low shrinkage ▪ Low coefficient of thermal expansion ▪ Good creep resistance ▪ Good resistance to vibration High reactivity for low temperature application (+10 °C) ▪ ▪ Impermeable to most liquids and water vapour PRODUCT INFORMATION Chemical base Epoxy resin, selected fillers and aggregates Packaging Part A+B+C pre-batched 26.5 kg Part A 4.5 kg container Part B 1.0 kg container Part C 21 kg bag

Product Details:

 91 000 74051 SikaRep® Microcrete-4 is a factory-blended, high-performance, non-shrink, cementitious micro-concrete mix. Designed for deep structural repairs in concrete, it flows easily into restricted forms, compensates for shrinkage, develops rapid strength, and bonds well with old concrete. Ideal for repairing damaged beams, slabs, columns, tunnels, basements, and large gapes. 
Key Features & Benefits 
Pourable / pumpable consistency; flows easily without the need for vibration. Dual-stage expansion to compensate for plastic shrinkage and settlement.
 Rapid strength gain: strong early (1-day, 3-day) strengths enabling quicker reinstatement. High ultimate strength with good impact, vibration, chemical resistance; non-corrosive, non-toxic. Contains no added chloride, so safer for reinforced concrete.
 Adjustable consistency by controlling water: you can adjust flow / workability while maintaining properties.
Q1. What is the price per 30 kg bag?Typical posted rates are around 000 per 30 kg bag, depending on Please visit CIVILIZEMARTQ2. How much area / volume will 1 bag cover?Consumption is approximately 1,900 kg of powder per cubic meter of concrete (with water : powder = 0.15). So 30 kg covers ~0.0158 m³ ~ about 15-16 liters volume roughly. Exact depends on depth / thickness. Q3. Can it be pumped?Yes — the product is designed to be pourable/pumpable into restricted formwork without vibration. Q4. Is it safe for reinforced concrete / steel?Yes — it is non-corrosive, contains no added chloride. Q5. What is shelf life & storage?Shelf life is ~6 months from date of production if stored in unopened bags, in dry conditions, at temperature between +5-35 °C. Q6. Can the mix be adjusted for more flow?Yes — by using water-powder ratio within the recommended range (0.14 to 0.16) for higher flow, but avoid adding more water than specified as that can degrade strengths & increase shrinkage.

Product Details:

 91 000 74051 SikaRep® Microcrete-4 is a factory-blended, high-performance, non-shrink, cementitious micro-concrete mix. Designed for deep structural repairs in concrete, it flows easily into restricted forms, compensates for shrinkage, develops rapid strength, and bonds well with old concrete. Ideal for repairing damaged beams, slabs, columns, tunnels, basements, and large gapes. 
Key Features & Benefits 
Pourable / pumpable consistency; flows easily without the need for vibration. Dual-stage expansion to compensate for plastic shrinkage and settlement.
 Rapid strength gain: strong early (1-day, 3-day) strengths enabling quicker reinstatement. High ultimate strength with good impact, vibration, chemical resistance; non-corrosive, non-toxic. Contains no added chloride, so safer for reinforced concrete.
 Adjustable consistency by controlling water: you can adjust flow / workability while maintaining properties.
Q1. What is the price per 30 kg bag?Typical posted rates are around 000 per 30 kg bag, depending on Please visit CIVILIZEMARTQ2. How much area / volume will 1 bag cover?Consumption is approximately 1,900 kg of powder per cubic meter of concrete (with water : powder = 0.15). So 30 kg covers ~0.0158 m³ ~ about 15-16 liters volume roughly. Exact depends on depth / thickness. Q3. Can it be pumped?Yes — the product is designed to be pourable/pumpable into restricted formwork without vibration. Q4. Is it safe for reinforced concrete / steel?Yes — it is non-corrosive, contains no added chloride. Q5. What is shelf life & storage?Shelf life is ~6 months from date of production if stored in unopened bags, in dry conditions, at temperature between +5-35 °C. Q6. Can the mix be adjusted for more flow?Yes — by using water-powder ratio within the recommended range (0.14 to 0.16) for higher flow, but avoid adding more water than specified as that can degrade strengths & increase shrinkage.

Product Details:

 91 000 74051 SikaRep® Microcrete-4 is a factory-blended, high-performance, non-shrink, cementitious micro-concrete mix. Designed for deep structural repairs in concrete, it flows easily into restricted forms, compensates for shrinkage, develops rapid strength, and bonds well with old concrete. Ideal for repairing damaged beams, slabs, columns, tunnels, basements, and large gapes. 
Key Features & Benefits 
Pourable / pumpable consistency; flows easily without the need for vibration. Dual-stage expansion to compensate for plastic shrinkage and settlement.
 Rapid strength gain: strong early (1-day, 3-day) strengths enabling quicker reinstatement. High ultimate strength with good impact, vibration, chemical resistance; non-corrosive, non-toxic. Contains no added chloride, so safer for reinforced concrete.
 Adjustable consistency by controlling water: you can adjust flow / workability while maintaining properties.
Q1. What is the price per 30 kg bag?Typical posted rates are around 000 per 30 kg bag, depending on Please visit CIVILIZEMARTQ2. How much area / volume will 1 bag cover?Consumption is approximately 1,900 kg of powder per cubic meter of concrete (with water : powder = 0.15). So 30 kg covers ~0.0158 m³ ~ about 15-16 liters volume roughly. Exact depends on depth / thickness. Q3. Can it be pumped?Yes — the product is designed to be pourable/pumpable into restricted formwork without vibration. Q4. Is it safe for reinforced concrete / steel?Yes — it is non-corrosive, contains no added chloride. Q5. What is shelf life & storage?Shelf life is ~6 months from date of production if stored in unopened bags, in dry conditions, at temperature between +5-35 °C. Q6. Can the mix be adjusted for more flow?Yes — by using water-powder ratio within the recommended range (0.14 to 0.16) for higher flow, but avoid adding more water than specified as that can degrade strengths & increase shrinkage.

Product Details:

  91 000 74051 Sika® Rustoff-100 is a single component liquid that removes rust and temporarily prevents further rusting of steel structures by providing a passivating coat. USES Sika® Rustoff-100 removes rust and temporarily prevents further rusting of: ▪ New or old reinforcement steel in construction ▪ Embedded steel in repairable structures ▪ ▪ Ball bearings, valves, tools etc. ▪ Various steel structures like tanks, water pipelines, effluent pipelines, trusses, purlins, rafters etc. Ideal for protecting reinforcements with insufficient cover or in thin sections.

Product Details:

 91 000 74051 SikaCeram-888 Tile Grout EP – Two-Component Epoxy Tile Grout & Adhesive (1 kg / 5 kg Sets) is a solvent-free, water-dispersed coloured epoxy tile grout & adhesive that is hygienic, hard-wearing, colourfast, chemical- and abrasion-resistant. Ideal for tiles, mosaics, porcelain, marble, etc. on walls & floors—especially where high cleanliness, moisture or chemical exposure is expected. Key Features & BenefitsVery good workability with long open time. Easy cleaning of joints with water; resistant to cracking and shrinkage. Impermeable to liquids and waterproof. High mechanical & abrasion resistance. Good chemical resistance—even steam cleaning; stainless & colour-fast.
Q1. What is open time and pot life?Open time is around 45 minutes. Mixed units (e.g. 100 g at 25 °C) have pot life approx 95 minutes before the mixture becomes difficult to work with. Q2. How soon can traffic or water immersion happen?Foot traffic safe after ~24 hours. Full cure in ~3 days. Water immersion after ~7 days. Q3. What joint width is possible?Can be used in joints from 1 mm up to 20 mm width. Q4. Is it stain-free & colour-safe for natural stone?Yes, it is stainless and colour-fast. But for natural stone or sensitive tiles, do a small test first. Q5. What is approximate price?Price typically depends on colour & size.Please contact Civiliz Mart or local Sika dealer for exact rates.

Product Details:

Sika® Raintite I is a multifunctional polymer emulsion for enhancing the properties of mortar/ concrete / grout/ cement slurry providing good adhesion, water resistance and improvement of several other properties.

Product Details:

It is a non-staining sealant that cures to a firm, flexible, tear-resistant rubber. DECK-O-SEAL GUN GRADE is highly resilient and has excellent recovery characteristics, even after extended periods of compression or elongation.

Product Details:

 91 000 74051 Sikadur-Combiflex® SG-10 P is a flexible waterproofingtape based on modified flexible Polyolefin (FPO) withadvanced adhesion properties. Thickness 1,0 mm.The product is part of the Sikadur Combiflex® SG System.USESSealing all types of joints and cracks in many differentstructures and applications including:▪ Tunnels and culverts▪ Hydroelectric power plants▪ Sewage treatment plants▪ Basements▪ Water retaining structures▪ Drinking water reservoirsSealing of:▪ Construction joints▪ Pipe penetrations▪ Cracks

Product Details:

 91 000 74051 Sikaflex® Construction is designed for movement and connection joints on porous substrates as well as indoor and outdoor sealing applications.
AdvantagesOne component, ready to useFast-curingNon-sagBubble-free curingCan be overpaintedHigh tear resistanceVery good adhesion to many substratesGood weather and ageing resistance

Product Details:

Sikadur®-31 C is solvent-free, moisture tolerant, twopart epoxy based thixotropic adhesive for bondingSikadur-Combiflex® SG tape and Sika® Dilatec® tape todifferent substrates. It can be used for both internaland external use.USESSikadur®-31 C may only be used by experienced professionals.As adhesive for the Sikadur-Combiflex® SystemAs adhesive for the Sika® Dilatec® SystemThese systems are used for various applications suchas:▪ Expansion Joint treatment▪ Construction Joint treatment▪ Crack treatment▪ Precast panels joint treatment

Product Details:

 Sikaflex®-11 FC+ is a 1-part, multipurpose elastic adhesive and joint sealant with very good application properties which bonds and seals most construction material substrates. Internal and external use. USES An adhesive to bond construction components and materials such as: ▪ Concrete ▪ Masonry ▪ Reconstituted or cast stone ▪ Ceramic ▪ Wood ▪ Metal ▪ Glass A sealant to seal vertical and horizontal joints

Product Details:

 91 000 74051 Sika Chapdur (IN) is a one-part, premixed, coloured mineral dry-shake hardener used for concrete floors. When broadcast and worked into fresh concrete, it creates an extremely hard-wearing, abrasion-resistant, dust-proof surface. Ideal for areas subject to heavy mechanical wear like warehouses, parking lots, factories, service stations, public floors, and more. 
Key Features & BenefitsReady to use; simple application method. High wear resistance & impact resistance. Dust-proof surface; easy to clean. Non-metallic, rust-free formula. Increased resistance to oils and grease.
Q1. What is the coverage of one 30 kg bag?A: For heavy duty (~5.5-6.0 kg/m²), one 30 kg bag will cover approximately 5 to 5.5 m². For lighter duty, higher coverage.Q2. Can I apply this on any concrete/slab?A: The substrate concrete must be good quality, fully compacted, with slump in the range ~75-110 mm. Compressive strength of the concrete should be at least ~20 N/mm². Surface should be clean and free of weak laitance. Q3. How long before the floor can be used?A: Foot traffic after ~72 hours; full service (heavier loads) after ~7 days, when fully cured. Q4. Is this product suitable where oil / grease / chemical spillage happens?A: Yes — the product has increased resistance to oils and grease. However, frequent cleaning and maintenance are needed.Q5. What precautions should I take during application?A:Do not apply in strong wind or excessively dry air.Do not add water over the dry shake once applied.Spread in two stages for better blending: first ~60% then ~40%.Use proper finishing tools (trowels, power trowels) to compact and smooth.Cure immediately after finishing, protect from rain or contamination.

Product Details:

91 000 74051  Sika® Rustop is cement bound synthetic resin modified 2-component coating for corrosion protection on reinforcement and concrete. Ideally suited to rehabilitate corroded reinforcement. USES Protects new or old reinforcement steel in construction from corrosion ▪ Ideal for protecting reinforcements with insufficient cover or in thin sections ▪ Protects embedded steel in repairable structures from further corrosion after rehabilitation ▪ Protects concrete against the action of Calcium Chlorides and de-icing salts

Product Details:

 91 000 74051 Sika MonoTop®-122 F trowelable mortar is a dual shrinkage compensated, thixotropic high strength formulation for structural concrete repairs. Sika MonoTop®-122 F is suitable for placing in thicknesses of 5mm to 50 mm vertically and 5-15mm overhead.

Product Details:

 91 000 74051 SikaGrout-214 IN is a one-component, ready-to-mix, dual shrinkage-compensated cementitious grout. It’s flowable and pourable, engineered for precision grouting of heavy base plates, machine foundations, anchors, precast concrete joints, voids and sealing around penetration points. It develops very high strength, remains impact and vibration resistant, and bonds excellently to concrete even under static and dynamic loads. 
Key Features & BenefitsDual shrinkage compensated – expansion during early phase to offset shrinkage. Wide temperature usage – works well from just above 0 °C up to +200 °C. Adjustable consistency – pourable or flowable depending on water/powder ratio. Rapid strength development – good strength even at early ages. Excellent bond to concrete; no bleeding or segregation. Chemical / frost / oil / fire resistant; non-corrosive to bolts and baseplates.
Q1. How should SikaGrout-214 IN be mixed?Add clean water (as per mix ratio: ~0.15-0.16 for flowable). Mix slowly, pour powder into water while stirring; use paddle mixer or low speed (<500 rpm) for large volumes. Let air escape after mixing before placing.Q2. What cure / pre-treatment is needed on substrate?Substrate must be structurally sound, clean, free of loose debris, oil, dust. Pre-soak substrate to saturated surface dry condition (keep wet but without standing water). Q3. What consistency options exist?Flowable: easier spread and pour.Pourable: thicker, for larger gaps or vertical uses. Adjust water accordingly within specified range.Q4. How soon can load be applied / equipment used?Compressive strength after 1 day is already ~25 N/mm². For heavy load, better to wait 7 days for higher strength.Q5. Is it safe for anchor bolts / base plates?Yes—non-corrosive, chloride-free, safe for reinforcement and bolts. Q6. What is an approximate price?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 Sika MonoTop®-122 F trowelable mortar is a dual shrinkage compensated, thixotropic high strength formulation for structural concrete repairs. Sika MonoTop®-122 F is suitable for placing in thicknesses of 5mm to 50 mm vertically and 5-15mm overhead.

Product Details:

 91 000 74051 Sika Chapdur (IN) is a one-part, premixed, coloured mineral dry-shake hardener used for concrete floors. When broadcast and worked into fresh concrete, it creates an extremely hard-wearing, abrasion-resistant, dust-proof surface. Ideal for areas subject to heavy mechanical wear like warehouses, parking lots, factories, service stations, public floors, and more. 
Key Features & BenefitsReady to use; simple application method. High wear resistance & impact resistance. Dust-proof surface; easy to clean. Non-metallic, rust-free formula. Increased resistance to oils and grease.
Q1. What is the coverage of one 30 kg bag?A: For heavy duty (~5.5-6.0 kg/m²), one 30 kg bag will cover approximately 5 to 5.5 m². For lighter duty, higher coverage.Q2. Can I apply this on any concrete/slab?A: The substrate concrete must be good quality, fully compacted, with slump in the range ~75-110 mm. Compressive strength of the concrete should be at least ~20 N/mm². Surface should be clean and free of weak laitance. Q3. How long before the floor can be used?A: Foot traffic after ~72 hours; full service (heavier loads) after ~7 days, when fully cured. Q4. Is this product suitable where oil / grease / chemical spillage happens?A: Yes — the product has increased resistance to oils and grease. However, frequent cleaning and maintenance are needed.Q5. What precautions should I take during application?A:Do not apply in strong wind or excessively dry air.Do not add water over the dry shake once applied.Spread in two stages for better blending: first ~60% then ~40%.Use proper finishing tools (trowels, power trowels) to compact and smooth.Cure immediately after finishing, protect from rain or contamination.

Product Details:

 91 000 74051 Sika Chapdur (IN) is a one-part, premixed, coloured mineral dry-shake hardener used for concrete floors. When broadcast and worked into fresh concrete, it creates an extremely hard-wearing, abrasion-resistant, dust-proof surface. Ideal for areas subject to heavy mechanical wear like warehouses, parking lots, factories, service stations, public floors, and more. 
Key Features & BenefitsReady to use; simple application method. High wear resistance & impact resistance. Dust-proof surface; easy to clean. Non-metallic, rust-free formula. Increased resistance to oils and grease.
Q1. What is the coverage of one 30 kg bag?A: For heavy duty (~5.5-6.0 kg/m²), one 30 kg bag will cover approximately 5 to 5.5 m². For lighter duty, higher coverage.Q2. Can I apply this on any concrete/slab?A: The substrate concrete must be good quality, fully compacted, with slump in the range ~75-110 mm. Compressive strength of the concrete should be at least ~20 N/mm². Surface should be clean and free of weak laitance. Q3. How long before the floor can be used?A: Foot traffic after ~72 hours; full service (heavier loads) after ~7 days, when fully cured. Q4. Is this product suitable where oil / grease / chemical spillage happens?A: Yes — the product has increased resistance to oils and grease. However, frequent cleaning and maintenance are needed.Q5. What precautions should I take during application?A:Do not apply in strong wind or excessively dry air.Do not add water over the dry shake once applied.Spread in two stages for better blending: first ~60% then ~40%.Use proper finishing tools (trowels, power trowels) to compact and smooth.Cure immediately after finishing, protect from rain or contamination.

Product Details:

 91 000 74051 Sika Injection-101 IN is a two-component, water-reactive polyurethane resin that foams when it contacts water, forming a flexible, hydrophobic closed-cell foam. It’s designed for stopping running water leaks, filling cracks and joints in concrete under hydrostatic pressure—ideal for foundations, tunnels, water tanks, retaining walls, basements etc. 
Key Features & Benefits
Low viscosity resin for deep penetration into cracks & voids. Produces a flexible, closed-cell foam that is hydrophobic and resists future water ingress. Reacts with water to foam up to ~40× its original volume. Fast gel time (~10 seconds) allowing quick sealing. Comes pre-batched (5 kg kit: 4.5 kg base + 0.5 kg catalyst) for ease of use. Suitable for use under hydrostatic pressure.
Q1. How is Sika Injection-101 IN applied?Clean the crack/joint (remove loose particles, oil, wax).Seal around the injection packer (if needed) to avoid resin escaping.Mix Part A (base) and Part B (catalyst) at ~90:10 ratio (or adjust within allowed limits for reaction time). Use injection pump to inject resin at low pressure, allow foam to expand and seal.Once set, clean away excess.Q2. What is gel time & cure time?Gel time is about 10 seconds at ~25-30 °C. Tack-free / initial curing takes ~2 hours. Q3. What are the packaging & storage details?Comes as a pre-batched 5.0 kg kit: 4.5 kg base (Part A) + 0.5 kg catalyst (Part B). Store in sealed, unopened containers at 5-30 °C. Shelf-life ~12 months. Q4. Is it safe for potable water or for use in drinking water tanks?It is hydrophobic and resistant to fungi/microorganisms. But products like this are generally for structural waterproofing, not for direct contact with potable water without checking specific approvals. Always check local PDS / safety data. Q5. What surface temperature and ambient conditions are needed?Both ambient and substrate temperatures should be between +10 °C to +40 °C. Q6. How much does it cost (rough estimate)?Please Visit or Contact CivilizeMart More Information

Product Details:

 91 000 74051 Sika MonoTop-108 Water Plug IN is a ready-to-use, rapid-setting, waterproof cement mortar designed to stop active water leaks instantly in concrete and masonry. It forms a strong, durable plug even under running water or high leak flow conditions, making it ideal for emergency repairs and plugging applications.
Key Use Cases: leaks through cracks, casting joints, gravel pockets; waterproofing water tanks, basements, sunken pits; sealing drainage outlets; during injection grouting. 
✔ Key Features & AdvantagesHardens within ~2-3 minutes at ~27 °C. Ready-to-use powder—just add water. Non-toxic and chloride-free—safe for potable water structures. Excellent adhesion to concrete, masonry, metals, PVC, HDPE etc. Low exotherm (less heat during curing), similar thermal expansion as concrete.
Q1. What kind of leaks can this stop?It can stop negative‐pressure leaks through cracks, joints, gravel pockets, casting joints etc.—even under running water. Q2. How fast does it set and become effective?At around 27 °C, it begins to harden in ~2-3 minutes. Quick strength gain ensures leak stops fast. Q3. How is the surface prepared before sealing?Clean area—remove loose materials, oil, grease etc. Widen leak point in “dovetail” shape (~20 mm) to allow better bonding. Wet the surface if very dry. Q4. How much material is needed?Depends on volume of leak / cavity. Since setting is very fast, mix small quantities at a time that you can apply immediately. For 1 kg bag, small area patch; for big leaks you may need multiple bags.Q5. Can it handle high pressure or lots of water flow?Yes—but for very high pressures, sometimes drill relief holes around the leak, or using supporting plugs, then apply the mortar. Larger bonding surface helps. Q6. Is it safe for potable water or areas that carry water later?Yes—it’s non-toxic and chloride free. Once cured, it can be used in water tanks, etc. Q7. What’s the price approx for a 5 kg bag?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 Sika MonoTop-108 Water Plug IN is a ready-to-use, rapid-setting, waterproof cement mortar designed to stop active water leaks instantly in concrete and masonry. It forms a strong, durable plug even under running water or high leak flow conditions, making it ideal for emergency repairs and plugging applications.
Key Use Cases: leaks through cracks, casting joints, gravel pockets; waterproofing water tanks, basements, sunken pits; sealing drainage outlets; during injection grouting. 
✔ Key Features & AdvantagesHardens within ~2-3 minutes at ~27 °C. Ready-to-use powder—just add water. Non-toxic and chloride-free—safe for potable water structures. Excellent adhesion to concrete, masonry, metals, PVC, HDPE etc. Low exotherm (less heat during curing), similar thermal expansion as concrete.
Q1. What kind of leaks can this stop?It can stop negative‐pressure leaks through cracks, joints, gravel pockets, casting joints etc.—even under running water. Q2. How fast does it set and become effective?At around 27 °C, it begins to harden in ~2-3 minutes. Quick strength gain ensures leak stops fast. Q3. How is the surface prepared before sealing?Clean area—remove loose materials, oil, grease etc. Widen leak point in “dovetail” shape (~20 mm) to allow better bonding. Wet the surface if very dry. Q4. How much material is needed?Depends on volume of leak / cavity. Since setting is very fast, mix small quantities at a time that you can apply immediately. For 1 kg bag, small area patch; for big leaks you may need multiple bags.Q5. Can it handle high pressure or lots of water flow?Yes—but for very high pressures, sometimes drill relief holes around the leak, or using supporting plugs, then apply the mortar. Larger bonding surface helps. Q6. Is it safe for potable water or areas that carry water later?Yes—it’s non-toxic and chloride free. Once cured, it can be used in water tanks, etc. Q7. What’s the price approx for a 5 kg bag?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 Sika MonoTop-108 Water Plug IN is a ready-to-use, rapid-setting, waterproof cement mortar designed to stop active water leaks instantly in concrete and masonry. It forms a strong, durable plug even under running water or high leak flow conditions, making it ideal for emergency repairs and plugging applications.
Key Use Cases: leaks through cracks, casting joints, gravel pockets; waterproofing water tanks, basements, sunken pits; sealing drainage outlets; during injection grouting. 
✔ Key Features & AdvantagesHardens within ~2-3 minutes at ~27 °C. Ready-to-use powder—just add water. Non-toxic and chloride-free—safe for potable water structures. Excellent adhesion to concrete, masonry, metals, PVC, HDPE etc. Low exotherm (less heat during curing), similar thermal expansion as concrete.
Q1. What kind of leaks can this stop?It can stop negative‐pressure leaks through cracks, joints, gravel pockets, casting joints etc.—even under running water. Q2. How fast does it set and become effective?At around 27 °C, it begins to harden in ~2-3 minutes. Quick strength gain ensures leak stops fast. Q3. How is the surface prepared before sealing?Clean area—remove loose materials, oil, grease etc. Widen leak point in “dovetail” shape (~20 mm) to allow better bonding. Wet the surface if very dry. Q4. How much material is needed?Depends on volume of leak / cavity. Since setting is very fast, mix small quantities at a time that you can apply immediately. For 1 kg bag, small area patch; for big leaks you may need multiple bags.Q5. Can it handle high pressure or lots of water flow?Yes—but for very high pressures, sometimes drill relief holes around the leak, or using supporting plugs, then apply the mortar. Larger bonding surface helps. Q6. Is it safe for potable water or areas that carry water later?Yes—it’s non-toxic and chloride free. Once cured, it can be used in water tanks, etc. Q7. What’s the price approx for a 5 kg bag?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 SikaGrout-214 IN is a one-component, ready-to-mix, dual shrinkage-compensated cementitious grout. It’s flowable and pourable, engineered for precision grouting of heavy base plates, machine foundations, anchors, precast concrete joints, voids and sealing around penetration points. It develops very high strength, remains impact and vibration resistant, and bonds excellently to concrete even under static and dynamic loads. 
Key Features & BenefitsDual shrinkage compensated – expansion during early phase to offset shrinkage. Wide temperature usage – works well from just above 0 °C up to +200 °C. Adjustable consistency – pourable or flowable depending on water/powder ratio. Rapid strength development – good strength even at early ages. Excellent bond to concrete; no bleeding or segregation. Chemical / frost / oil / fire resistant; non-corrosive to bolts and baseplates.
Q1. How should SikaGrout-214 IN be mixed?Add clean water (as per mix ratio: ~0.15-0.16 for flowable). Mix slowly, pour powder into water while stirring; use paddle mixer or low speed (<500 rpm) for large volumes. Let air escape after mixing before placing.Q2. What cure / pre-treatment is needed on substrate?Substrate must be structurally sound, clean, free of loose debris, oil, dust. Pre-soak substrate to saturated surface dry condition (keep wet but without standing water). Q3. What consistency options exist?Flowable: easier spread and pour.Pourable: thicker, for larger gaps or vertical uses. Adjust water accordingly within specified range.Q4. How soon can load be applied / equipment used?Compressive strength after 1 day is already ~25 N/mm². For heavy load, better to wait 7 days for higher strength.Q5. Is it safe for anchor bolts / base plates?Yes—non-corrosive, chloride-free, safe for reinforcement and bolts. Q6. What is an approximate price?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 SikaGrout-214 IN is a one-component, ready-to-mix, dual shrinkage-compensated cementitious grout. It’s flowable and pourable, engineered for precision grouting of heavy base plates, machine foundations, anchors, precast concrete joints, voids and sealing around penetration points. It develops very high strength, remains impact and vibration resistant, and bonds excellently to concrete even under static and dynamic loads. 
Key Features & BenefitsDual shrinkage compensated – expansion during early phase to offset shrinkage. Wide temperature usage – works well from just above 0 °C up to +200 °C. Adjustable consistency – pourable or flowable depending on water/powder ratio. Rapid strength development – good strength even at early ages. Excellent bond to concrete; no bleeding or segregation. Chemical / frost / oil / fire resistant; non-corrosive to bolts and baseplates.
Q1. How should SikaGrout-214 IN be mixed?Add clean water (as per mix ratio: ~0.15-0.16 for flowable). Mix slowly, pour powder into water while stirring; use paddle mixer or low speed (<500 rpm) for large volumes. Let air escape after mixing before placing.Q2. What cure / pre-treatment is needed on substrate?Substrate must be structurally sound, clean, free of loose debris, oil, dust. Pre-soak substrate to saturated surface dry condition (keep wet but without standing water). Q3. What consistency options exist?Flowable: easier spread and pour.Pourable: thicker, for larger gaps or vertical uses. Adjust water accordingly within specified range.Q4. How soon can load be applied / equipment used?Compressive strength after 1 day is already ~25 N/mm². For heavy load, better to wait 7 days for higher strength.Q5. Is it safe for anchor bolts / base plates?Yes—non-corrosive, chloride-free, safe for reinforcement and bolts. Q6. What is an approximate price?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 SikaGrout-214 IN is a one-component, ready-to-mix, dual shrinkage-compensated cementitious grout. It’s flowable and pourable, engineered for precision grouting of heavy base plates, machine foundations, anchors, precast concrete joints, voids and sealing around penetration points. It develops very high strength, remains impact and vibration resistant, and bonds excellently to concrete even under static and dynamic loads. 
Key Features & BenefitsDual shrinkage compensated – expansion during early phase to offset shrinkage. Wide temperature usage – works well from just above 0 °C up to +200 °C. Adjustable consistency – pourable or flowable depending on water/powder ratio. Rapid strength development – good strength even at early ages. Excellent bond to concrete; no bleeding or segregation. Chemical / frost / oil / fire resistant; non-corrosive to bolts and baseplates.
Q1. How should SikaGrout-214 IN be mixed?Add clean water (as per mix ratio: ~0.15-0.16 for flowable). Mix slowly, pour powder into water while stirring; use paddle mixer or low speed (<500 rpm) for large volumes. Let air escape after mixing before placing.Q2. What cure / pre-treatment is needed on substrate?Substrate must be structurally sound, clean, free of loose debris, oil, dust. Pre-soak substrate to saturated surface dry condition (keep wet but without standing water). Q3. What consistency options exist?Flowable: easier spread and pour.Pourable: thicker, for larger gaps or vertical uses. Adjust water accordingly within specified range.Q4. How soon can load be applied / equipment used?Compressive strength after 1 day is already ~25 N/mm². For heavy load, better to wait 7 days for higher strength.Q5. Is it safe for anchor bolts / base plates?Yes—non-corrosive, chloride-free, safe for reinforcement and bolts. Q6. What is an approximate price?PLEASE VISIT CIVILIZEMART

Product Details:

 91 000 74051 Sika Injection-101 IN is a two-component, water-reactive polyurethane resin that foams when it contacts water, forming a flexible, hydrophobic closed-cell foam. It’s designed for stopping running water leaks, filling cracks and joints in concrete under hydrostatic pressure—ideal for foundations, tunnels, water tanks, retaining walls, basements etc. 
Key Features & Benefits
Low viscosity resin for deep penetration into cracks & voids. Produces a flexible, closed-cell foam that is hydrophobic and resists future water ingress. Reacts with water to foam up to ~40× its original volume. Fast gel time (~10 seconds) allowing quick sealing. Comes pre-batched (5 kg kit: 4.5 kg base + 0.5 kg catalyst) for ease of use. Suitable for use under hydrostatic pressure.
Q1. How is Sika Injection-101 IN applied?Clean the crack/joint (remove loose particles, oil, wax).Seal around the injection packer (if needed) to avoid resin escaping.Mix Part A (base) and Part B (catalyst) at ~90:10 ratio (or adjust within allowed limits for reaction time). Use injection pump to inject resin at low pressure, allow foam to expand and seal.Once set, clean away excess.Q2. What is gel time & cure time?Gel time is about 10 seconds at ~25-30 °C. Tack-free / initial curing takes ~2 hours. Q3. What are the packaging & storage details?Comes as a pre-batched 5.0 kg kit: 4.5 kg base (Part A) + 0.5 kg catalyst (Part B). Store in sealed, unopened containers at 5-30 °C. Shelf-life ~12 months. Q4. Is it safe for potable water or for use in drinking water tanks?It is hydrophobic and resistant to fungi/microorganisms. But products like this are generally for structural waterproofing, not for direct contact with potable water without checking specific approvals. Always check local PDS / safety data. Q5. What surface temperature and ambient conditions are needed?Both ambient and substrate temperatures should be between +10 °C to +40 °C. Q6. How much does it cost (rough estimate)?Please Visit or Contact CivilizeMart More Information

Product Details:

 91 000 74051 Sika Injection-101 IN is a two-component, water-reactive polyurethane resin that foams when it contacts water, forming a flexible, hydrophobic closed-cell foam. It’s designed for stopping running water leaks, filling cracks and joints in concrete under hydrostatic pressure—ideal for foundations, tunnels, water tanks, retaining walls, basements etc. 
Key Features & Benefits
Low viscosity resin for deep penetration into cracks & voids. Produces a flexible, closed-cell foam that is hydrophobic and resists future water ingress. Reacts with water to foam up to ~40× its original volume. Fast gel time (~10 seconds) allowing quick sealing. Comes pre-batched (5 kg kit: 4.5 kg base + 0.5 kg catalyst) for ease of use. Suitable for use under hydrostatic pressure.
Q1. How is Sika Injection-101 IN applied?Clean the crack/joint (remove loose particles, oil, wax).Seal around the injection packer (if needed) to avoid resin escaping.Mix Part A (base) and Part B (catalyst) at ~90:10 ratio (or adjust within allowed limits for reaction time). Use injection pump to inject resin at low pressure, allow foam to expand and seal.Once set, clean away excess.Q2. What is gel time & cure time?Gel time is about 10 seconds at ~25-30 °C. Tack-free / initial curing takes ~2 hours. Q3. What are the packaging & storage details?Comes as a pre-batched 5.0 kg kit: 4.5 kg base (Part A) + 0.5 kg catalyst (Part B). Store in sealed, unopened containers at 5-30 °C. Shelf-life ~12 months. Q4. Is it safe for potable water or for use in drinking water tanks?It is hydrophobic and resistant to fungi/microorganisms. But products like this are generally for structural waterproofing, not for direct contact with potable water without checking specific approvals. Always check local PDS / safety data. Q5. What surface temperature and ambient conditions are needed?Both ambient and substrate temperatures should be between +10 °C to +40 °C. Q6. How much does it cost (rough estimate)?Please Visit or Contact CivilizeMart More Information

Product Details:

 91 000 74051 SikaLatex® SBR is a superior modified styrene butadiene emulsion to be mixed with cement slurry, cement mortar, concrete or cementitious grout for improved adhesion and water resistance properties. It is fully soluble in water and is added directly to the gauging water of slurry, mortar, concrete or grout. 

Product Details:

 91 000 74051 Sika MonoTop®-122 F trowelable mortar is a dual shrinkage compensated, thixotropic high strength formulation for structural concrete repairs. Sika MonoTop®-122 F is suitable for placing in thicknesses of 5mm to 50 mm vertically and 5-15mm overhead.

Product Details:

 91 000 74051 SikaRep® Microcrete-4 is a factory-blended, high-performance, non-shrink, cementitious micro-concrete mix. Designed for deep structural repairs in concrete, it flows easily into restricted forms, compensates for shrinkage, develops rapid strength, and bonds well with old concrete. Ideal for repairing damaged beams, slabs, columns, tunnels, basements, and large gapes. 
Key Features & Benefits 
Pourable / pumpable consistency; flows easily without the need for vibration. Dual-stage expansion to compensate for plastic shrinkage and settlement.
 Rapid strength gain: strong early (1-day, 3-day) strengths enabling quicker reinstatement. High ultimate strength with good impact, vibration, chemical resistance; non-corrosive, non-toxic. Contains no added chloride, so safer for reinforced concrete.
 Adjustable consistency by controlling water: you can adjust flow / workability while maintaining properties.
Q1. What is the price per 30 kg bag?Typical posted rates are around 000 per 30 kg bag, depending on Please visit CIVILIZEMARTQ2. How much area / volume will 1 bag cover?Consumption is approximately 1,900 kg of powder per cubic meter of concrete (with water : powder = 0.15). So 30 kg covers ~0.0158 m³ ~ about 15-16 liters volume roughly. Exact depends on depth / thickness. Q3. Can it be pumped?Yes — the product is designed to be pourable/pumpable into restricted formwork without vibration. Q4. Is it safe for reinforced concrete / steel?Yes — it is non-corrosive, contains no added chloride. Q5. What is shelf life & storage?Shelf life is ~6 months from date of production if stored in unopened bags, in dry conditions, at temperature between +5-35 °C. Q6. Can the mix be adjusted for more flow?Yes — by using water-powder ratio within the recommended range (0.14 to 0.16) for higher flow, but avoid adding more water than specified as that can degrade strengths & increase shrinkage.

Product Details:

 91 000 74051 Sika MonoTop®-122 F trowelable mortar is a dual shrinkage compensated, thixotropic high strength formulation for structural concrete repairs. Sika MonoTop®-122 F is suitable for placing in thicknesses of 5mm to 50 mm vertically and 5-15mm overhead.

Product Details:

91 000 74051 SikaLatex® Power is a latex-based, water-resistant multipurpose admixture for use in areas subject to humidity, dampness and continuous water contact. When added to cement mixtures, it improves water resistance and bonding strength by forming a reinforcing polymer that increases long term durability and flexibility of the mix. It is fully soluble in water and is to be added directly to the gauging water of mortar, concrete or cementitious grout.

Product Details:

 91 000 74051 Sika Injection-101 IN is a two-component, water-reactive polyurethane resin that foams when it contacts water, forming a flexible, hydrophobic closed-cell foam. It’s designed for stopping running water leaks, filling cracks and joints in concrete under hydrostatic pressure—ideal for foundations, tunnels, water tanks, retaining walls, basements etc. 
Key Features & Benefits
Low viscosity resin for deep penetration into cracks & voids. Produces a flexible, closed-cell foam that is hydrophobic and resists future water ingress. Reacts with water to foam up to ~40× its original volume. Fast gel time (~10 seconds) allowing quick sealing. Comes pre-batched (5 kg kit: 4.5 kg base + 0.5 kg catalyst) for ease of use. Suitable for use under hydrostatic pressure.
Q1. How is Sika Injection-101 IN applied?Clean the crack/joint (remove loose particles, oil, wax).Seal around the injection packer (if needed) to avoid resin escaping.Mix Part A (base) and Part B (catalyst) at ~90:10 ratio (or adjust within allowed limits for reaction time). Use injection pump to inject resin at low pressure, allow foam to expand and seal.Once set, clean away excess.Q2. What is gel time & cure time?Gel time is about 10 seconds at ~25-30 °C. Tack-free / initial curing takes ~2 hours. Q3. What are the packaging & storage details?Comes as a pre-batched 5.0 kg kit: 4.5 kg base (Part A) + 0.5 kg catalyst (Part B). Store in sealed, unopened containers at 5-30 °C. Shelf-life ~12 months. Q4. Is it safe for potable water or for use in drinking water tanks?It is hydrophobic and resistant to fungi/microorganisms. But products like this are generally for structural waterproofing, not for direct contact with potable water without checking specific approvals. Always check local PDS / safety data. Q5. What surface temperature and ambient conditions are needed?Both ambient and substrate temperatures should be between +10 °C to +40 °C. Q6. How much does it cost (rough estimate)?Please Visit or Contact CivilizeMart More Information

Product Details:

 91 000 74051  SikaTop®-107 Seal IN is a two part, acrylic polymer modified cementitious liquid applied waterproofing coating system. It comprises of a liquid polymer and a cement based mix incorporating special admixtures. It is applied to concrete and mortar to prevent water in filtration.

Product Details:

 91 000 74051 SikaLatex® SBR is a superior modified styrene butadiene emulsion to be mixed with cement slurry, cement mortar, concrete or cementitious grout for improved adhesion and water resistance properties. It is fully soluble in water and is added directly to the gauging water of slurry, mortar, concrete or grout. 

Product Details:

 91 000 74051 SikaShield® Primer W-30 IN is single component, quick drying, water based modified bituminous primer which penetrates and activates the substrates. It improves adhesion between the substrate and preformed bituminous sheet membranes in SikaShield® range. 

Product Details:

 91 000 74051 SikaLatex® Power is a latex-based, water-resistant multipurpose admixture for use in areas subject to humidity, dampness and continuous water contact. When added to cement mixtures, it improves water resistance and bonding strength by forming a reinforcing polymer that increases long term durability and flexibility of the mix. It is fully soluble in water and is to be added directly to the gauging water of mortar, concrete or cementitious grout.

Product Details:

 91 000 74051 Sika® CemCrete is a multifunctional acrylic polymer emulsion for enhancing the properties of cement slurry or mortar. It provides a good adhesion, water resistance and improvement of several other properties.

Product Details:

 91 000 74051 SikaLatex® Super is a specialised modified styrene butadiene emulsion to be mixed with cement slurry, cement mortar, concrete or cementitious grout for improved adhesion and water resistance properties. It is fully soluble in water and is added directly to the gauging water of slurry, mortar, concrete or grout.