Civilize Mart

VB-Premium Ready is a ready mix cement plaster/render with high quality polymers, water proofing integrated chemicals well graded sand and fillers for manual plastering applications

Product DescriptionGROUT 700 NS is supplied as a ready to use dry powder. The addition of a controlled amount of clean water produces a free-flowing, non-shrink grout for gap thicknesses up to 100mm.
GROUT 700 NS is a blend of Portland cement, graded fillers, and chemical additives which impart controlled expansion in the plastic state whilst minimizing water demand. The low water demand ensures high early strength. The graded fillers are designed to assist uniform mixing and produce a consistent grout. 
Areas of Application:Heavy machinery & equipment foundation.Bridge bearing pad & structural columns in pre-cast crane rail construction grouting.Boiler foundation & turbine generator bearing plates.Cavities, gaps, recesses and anchorage. 
Surface PreparationThe substrate surface must be free from oil, grease or any loosely adherent material.If the concrete surface is defective or has laitance, it must be cut back to a sound base.Bolt holes and fixing pockets must be blown clean of any dirt or debris.
MixingFor best results, a mechanically powered grout mixer should be used.When quantities up to 50kg are used, a heavy-duty slow speed drill (400-500 rpm) fitted with a paddle is suitable.Larger quantities will require a heavy-duty mixer.To enable the grouting operation to be carried out continuously, it is essential that sufficient mixing capacity and labor are available.The use of a grout holding tank with provision to gently agitate the grout may be required.
Application At 300C place the grout within 20 minutes of mixing to gain the full benefit of the expansion process.GROUT 700 NS can be placed in thicknesses up to 100mm in a single pour when used as an underplate grout.For thicker sections, it is necessary to fill out VGrout 700 with well-graded silt free aggregate to minimize heat buildup. Typically a 10mm aggregate is suitable. 50 - 100% aggregate weight of GROUT 700 NS can be added.Any bolt pockets must be grouted prior to grouting between the substrate and the base plate.Continuous grout flow is essential. Sufficient grout must be prepared before starting.The time taken to pour a batch must be regulated to the time to prepare the next one.
Advantages:Gaseous expansion system compensates for shrinkage and settlement in the plastic stateNo metallic iron content to cause stainingPre-packed material overcomes onsite batching variationsDevelops high early strength without the use of chloridesHigh ultimate strength ensure the durability of the hardened groutFree flow ensures a high level of contact with the load-bearing area
Precautions & Limitations:Low temperature working: When the air or contact surface temperatures are 100C or below on a falling thermometer, warm water (30 - 400C) is recommended to accelerate strength development.For ambient temperature below 100C, the formwork should be kept in place for at least 36 hours. Normal precautions for winter working with cementitious materials should then be adopted.High temperature working: At ambient temperatures above 400 C, cool water (below 200C) should be used for mixing the grout prior to placement.Fire: GROUT 700 NS is non-flammable.

VBOND AAC BLOCK MORTOR is a factory prepared blend of carefully selected raw materials, Portland cement and graded aggregates and polymers. Designed for use with water to produce high strength thixotropic mortar, for laying Aerated Light weight concrete, Fly ash bricks, cement hollow blocks, Cellular concrete blocks or smoothing over the block work surface in layers of up to 12mm thickness, that meet and exceed the requirements of National and International Standards.

 91 000 74051 VBOND Block jointing mortar is a superior water-resistant cement based mortar designed specifically for joining blocks. This mortar is specially designed & manufactured to provide superior adhesive strength, higher longevity and a strong bond between the blocks under strict quality controls. It also ensures higher bond at any thickness.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 Dubara Plaster is a specially formulated blend of Portland cement, fine graded sand, and water-soluble, high-quality polymer additives, precisely proportioned to create a versatile & ready-to-use mixture. With its simple preparation process, it can be easily mixed with water on-site, making it ideal for applying as a second Coat on bricks, blocks, and concrete surfaces

 91 000 74051 VBOND Wall Textures, a unique concept in wall coverings, that combines textures and colors to create an exciting alternative to Wall paper, Tiles & other coatings. Available in two ariants -Natural Grit finish (Two Component : 25 + 5 Kg) and Designer Textures (25 Kg). With VBOND Wall Textures, you can elevate the aesthetic appeal of your living spaces in a way that's both artistic and functional.

 91 000 74051 Epoxy Tile Grout is a highly effective & versatile grouting material, composed of three essential components: resin, hardener, & filler powder, where the fEpoxy Tile Grout is a highly effective & versatile grouting material, composed of three essential components: resin, hardener, & filler powder, where the filler powder serves as the color component. This unique tricomponent formulation is specifically designed to offer exceptional performance & durability when used to seal & fill the gaps between tilesiller powder serves as the color component. This unique tricomponent formulation is specifically designed to offer exceptional performance & durability when used to seal & fill the gaps between tiles

 91 000 74051 VBOND Unsanded Grout is a premium formulation comprising Portland cement, advanced polymers, special grade minerals. It is expertly crafted for use with Bond Grout Admix Plus, particularly in narrow joints up to 3mm wide. This grout excels at grouting porous & absorbent tiles, delivering a flawless final result thanks to its exceptional compatibility.

 91 000 74051 Take your tiling endeavors to new heights by incorporating our meticulously engineered Vepoxy grout. This innovative grouting solution is designed to elevate both the visual appeal and functionality of your projects, offering compatibility with a wide array of tile types

 91 000 74051 Con Repair SBR Latex is an innovative solution designed for various construction applications. It's a modified styrene butadiene emulsion that excels as a bonding agent & gauging liquid in cementitious systems. Explore its outstanding features and uses.

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

•  91 000 74051 VEPOXY SP GOLD is a two-component (resin + hardener + filler-powder) epoxy tile grout for grouting tile joints — i.e. filling the gaps between tiles, not for sticking tiles to floor/wall. 

• It’s meant for ceramic tiles, vitrified tiles, natural stone (marble/granite), glass-mosaic, and other tile/stone surfaces.

• Target use: areas where hygiene, water-resistance, stain-resistance and durability matter — kitchens, bathrooms, swimming pools, hospitals, restaurants, heavy-traffic floors and wet/water-exposed surfaces. 

�� Technical Specs & Properties ✅ Advantages & When You Should Use It

Use VEPOXY SP GOLD when you need:

• Durable grout joints — for high-traffic floors, commercial kitchens, pool decks, bathrooms, etc. Because it’s epoxy-based it’s more durable than regular cement-based grout.

• Waterproof, stain-proof & hygienic finish — good for kitchens, bathrooms, hospitals, restaurants, swimming pools or any wet / hygiene-sensitive area.

• Strong chemical, acid, alkali resistance — useful where cleaning chemicals, detergents, grease, or moisture are frequent.

• Minimal maintenance & long life — thanks to non-shrinking, non-cracking, anti-fungal, stain-resistant and water-resistant properties.

• Vertical or horizontal surfaces — clings well to vertical surfaces too, so usable for wall tiles as well as floors. 

⚠️ How to Use — Important Considerations

• Ensure tiles & joints are clean, dry and free of dust/debris before grouting.

• Mix properly: combine resin (Part A), hardener (Part B) and filler (Part C) thoroughly. Use a low-speed stirrer to avoid overheating (which reduces pot life). 

• Work the mixed grout within 40–45 min (pot-life), finish grouting, and clean off excess grout from tile surfaces before it starts to set. 

• Avoid leaving excess grout on tile surface as it may cure to hard film — clean off promptly with sponge / float. 

• Allow full curing / drying before exposing to heavy traffic or water — generally 24 hrs for foot-traffic safe, but full chemical / water-resistance likely needs curing as per instructions. 

•  91 000 74051 According to manufacturer documentation, “Platinum Plus – 3335” is a Type-3 / “Super-Flex / heavy-duty” cementitious, polymer-modified, thin-bed tile adhesive. 

• It’s designed for floor and wall applications, indoors as well as outdoors, and is suitable for large-format tiles, natural stones (like marble/granite), vitrified tiles, mosaic & glass tiles. 

• It offers high bond strength, flexibility, shock/impact resistance, and is water-resistant — making it fit for demanding conditions including wet areas (bathrooms, kitchens, even pool surroundings) when installed properly. 

�� Packaging & Coverage

• Comes in a 20 kg bag. 

• Coverage is approximately 55–60 sq.ft per 20 kg bag when applied with a 6 mm × 6 mm notched trowel — actual coverage depends on tile size, substrate flatness and thickness of adhesive bed.

�� Where & When to Use It

Use 3335 Platinum Plus when you need:

• Laying large-format tiles, heavy stone tiles (granite / marble) or vitrified tiles on floor or walls.

• Interior floors/walls, exterior surfaces, wet zones (bathrooms, kitchens), terraces, balconies, etc.

• High-traffic areas or heavy load zones (corridors, commercial areas), where strength and bond durability matter.

• Strong, water-resistant, shock-resistant installation — e.g. for kitchens, bathrooms, pool-side tiling etc. 

✅ Key Advantages

• High bonding strength and durability — reliably holds tiles and stones even under load or heavy use. 

• Water-resistant and suitable for wet areas, which reduces risk of loosening or tile failures in wet zones.Works for large format tiles and stone — good for premium flooring or stone cladding work. 

• Convenient to use (single-component, polymer-modified cement-based adhesive), eliminating need for complicated mixing beyond water. 

⚠️ What to Keep in Mind / Check Before Use

• Ensure surface/substrate is clean, level, stable and properly prepared (free from dust/oil/loose particles) before applying adhesive — as with any tile adhesive.

• For large tiles or heavy stones, it might be recommended to “back-butter” (i.e. apply adhesive on the back of the tile as well) to ensure full contact and avoid hollow spots under tiles. 

• While adhesive is water-resistant, if you’re tiling in continuously wet or external exposed areas (exterior walls, pool-side, heavy rains) ensure overall waterproofing measures are taken (substrate waterproofing + proper grout).

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

•  91 000 74051 V-Bond GOLD PLUS is a “single-component thin-bed adhesive / dry-mix mortar” — cement-based and polymer-modified, ready-to-use for tiling jobs.

• It’s classified as a Type-2 / “extra-premium” tile adhesive designed for strong bonding. 

• It’s meant for tiles and stones on floors, walls, countertops, etc — in internal (and often external) surfaces. 

�� Key Features & Benefits

• High bond strength — gives firm adhesion for tiles/stones on different substrates. 

• Flexible & shock/impact resistant — helps handle minor movements or stress without cracking. 

• Water-resistant — suitable for damp or wet areas (bathrooms, kitchens, maybe even pool-sides depending on tile & spec) when used properly.

• Self-curing and easy to use — simpler than traditional cement-sand mortar; less labour-intensive, likely more consistent.

• Helps avoid “hollowness” (tile not sticking well or gaps under tile) — leads to durable, stable tile installation. 

�� Where & When to Use It

Good for:

• Floor and wall tile installations (ceramic, vitrified, stone, etc.) — in houses, apartments, offices.

• Kitchens, bathrooms, wet areas — due to water-resistance.

• Heavy-duty or high-traffic areas (because of strong bond + shock resistance).

• Renovation or new construction where you want reliable long-lasting tile laying with less risk of tiles loosening or cracking.

✅ What to Check Before Use

• Make sure surface is clean and prepared before applying adhesive.

• Use appropriate water mixing / application instructions (as per manufacturer) — because being “ready to use / single component” doesn’t mean “ignore surface prep.”

• For exterior/wet areas: ensure tiles and grout are suitable for water exposure, and that overall waterproofing is considered — adhesive helps but isn’t complete waterproofing by itself.

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

 91 000 74051 VFIX-GOLD PLUS Extra Premium Tile Adhesive Type-2 for Tiles is a Single component thin bed adhesive which is ready to use Cement based Polymer modified dry mix mortar for fixing various types of tiles and stones for floor, wall and counter tops. Specially designed for heavy duty application for fixing variety of tiles on internal vertical and horizontal surfaces. This highly flexible adhesive also has a good water resisting ability. When properly installed, it takes care of hollowness problems and very ideal for green buildings. 

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.

 91 000 74051 VBOND Ready Plaster is a blend of Portland cement, finely graded sand & water soluble high-quality polymer additives in the Specified proportion. This mixture is ready to use by mixing with water at the site & can be applied on bricks, blocks, and concrete surfaces.